valutazioni - 2, GPA: 4
(
)
)
|
Facilità d'uso
Alterations could result in electric shock, injury, fire, or damage to the unit. 3 I. Specifications A. Construction Top Panel Ice Making Mechanism Scoop Holder Front Panel Control Switch Louver Bin Control Thermostat Bulb Slope Magnet Catch Door Power Cord B. Nameplate Rating PERLICK ICE MAKER MODEL NUMBER H50IMS-R SERIAL NUMBER AC SUPPLY VOLTAGE 115-120/60/1AMPERES 3.4 AMPS DESIGN PRESSURE HI-240PSI LO-120PSI REFRIGERANT 134a 4.2 oz. MOTOR-COMPRESSOR THERMALLY PROTECTED APPROVED FOR OUTDOOR USE Perlick Corp. Milwaukee, WI 53223 ICE MAKER 946Z Note: Only the "MODEL NUMBER" is replaced for other models. See the nameplate for electrical and refrigeration specifications. This nameplate is located inside the bin on the right side. We reserve the right to make changes in specifications and design without prior notice. 5 Units: mm [in.] C. Dimensions/Connections 1. H50IMS-R, H-50IMS-L 2. H50IMW Units: mm [in.] 7 3. H50IMS-ADL, H50IMS-ADR Units: mm [in.] 4. H50IMW-AD Units: mm [in.] 9 II. Installation and Operating Instructions WARNING 1. This icemaker must be installed in accordance with applicable national, state, and local regulations. 2. CHOKING HAZARD: Ensure all components, fasteners, and thumbscrews are securely in place after installation. Make sure that none have fallen into the storage bin. A. Checks Before Installation • Visually inspect the exterior of the shipping container and immediately report any damage to the carrier. Upon opening the container, any concealed damage should also be immediately reported to the carrier. • Remove the shipping carton, tape, and packing material. If any are left in the icemaker, it will not work properly. • Remove the package containing the accessories. • Remove the protective plastic film from the panels. If the icemaker is exposed to the sun or to heat, remove the film after the icemaker cools. • See the nameplate inside the bin on the right side, and check that your voltage supplied corresponds with the voltage specified on the nameplate. B. Location 1. General This icemaker is approved for indoor or outdoor use. CAUTION 1. Normal operating ambient temperature should be within 45°F to 100°F (7°C to 38°C); Normal operating water temperature should be within 45°F to 95°F (7°C to 35°C). Operation of the icemaker, for extended periods, outside of these normal temperature ranges may affect icemaker performance. 2. This icemaker will not work at sub-freezing temperatures. To prevent damage to the water supply line, drain the icemaker if the air temperature is going to go below 32°F (0°C). See "III.C. Preparing the Icemaker for Long Storage." For best operating results: • The icemaker should not be located next to ovens, grills, or other high heat producing equipment. • The location should provide a firm foundation for the icemaker. • This icemaker requires no side or top clearance. But allow enough space at rear for water supply and drain connections and at least 15" (38 cm) clearance at front. 10 Support: Do notMin. 15" (381 mm) H50IMS-R/L H50IMW Min. 34" Oven Icemaker 2. Built-In Installation Site CAUTION 1. Do not let the weight of the counter rest on the icemaker. 2. Do not install the icemaker in a corner where the door will interfere with other equipment or where the icemaker cannot be pulled out for service. Installation Space Model Height Width Depth H50IMS-R/L H50IMW 34" (864 mm) minimum 15" (381 mm) minimum 24" (610 mm) minimumH50IMS-ADR/ADL H50IMW-AD 32" (814 mm) minimum Between Two Cabinets Between a Cabinet and the End of a Counter H50IMS-R/LH50IMWMin. 34" (864 mm) Min. 15" (381 mm) H50IMS-R/L H50IMW Min. 34" (864 mm) H50IMS-ADR/ADL H50IMS-ADR/ADLH50IMS-ADR/ADLH50IMW H50IMWH50IMW- --AD ADAD Min. 32" Min. 32"Min. 32" (814 mm) (814 mm)(814 mm) let the weight of (864 mm) the counter rest H50IMS-ADR/ADL on the icemaker H50IMW-AD Min. 32" (814 mm) In a Corner Between a Cabinet and a Wall or Tall Cabinet Secure: Do not let the weight of the counter rest on the icemaker 4 7/8" minimum distance from corner to achieve desired door opening clearance 105° minimum door swing for convenient access to ice bin 11 C. Door Overlay Panel Fabrication and Attachment (H50IMW, H50IMW-AD) IMPORTANT The overlay panel must be crafted by a professional cabinet maker to ensure quality results. (1) Parts Ensure that all parts required for the overlay panel assembly are contained in the accessories bag. Overlay Panel Parts No. Description Part Number Qty. 1 Threaded Wood Insert 4A4004-01 6 2 T2 Screw 4.8 SS 7P32-0408 3 3 Pan Head Screw M4.25 SS 7C12-0425 4 4 Truss Head Screw M4.8 SS 7C32-0408 2 5 Canoe Clip 4A0629-02 2 6 Sheet Metal Bracket 4A3998-01 1 1 2 3 4 6 5 12 (2) Overlay Panel Specification Use the specification that applies to your icemaker (H50IMW or H50IMW-AD) and the directions that follow to prepare your overlay panel. (a) H50IMW .................... H50IMW Overlay Panel Specification Overlay Panel Height 29 17/32" (750 mm) Overlay Panel Width 14 13...
Questo manuale è adatto anche per i modelli :Altri elettrodomestici da cucina - SELF CONTAINED H50IMS-ADL (2.26 mb)
Altri elettrodomestici da cucina - SELF CONTAINED H50IMS-ADR (2.26 mb)
Altri elettrodomestici da cucina - SELF CONTAINED H50IMS-R (2.26 mb)
Altri elettrodomestici da cucina - SELF CONTAINED H50IMW (2.26 mb)