Log:
valutazioni - 4, GPA: 4.3 ( )

Istruzioni per l'uso Electrolux, Modello 5995421640

Produttore : Electrolux
File Size : 861.03 kb
File Nome : E15IM60EPS_om_en.pdf
Lingua di insegnamento: en
Vai a scaricare



Facilità d'uso


! CA CACACACACAUTION UTIONUTIONUTIONUTIONUTION DO NOT use any type of cleaner on the condenser unit. 3 Clean the condenser coil using a brush with a “combing” action, or a vacuum cleaner. Do not touch the condenser coil. 4 Position the grille to align the screw holes with the cabinet. 5 Insert the grille screws and tighten. Do not over tighten. 28 1 Set the cycle selector switch to OFF and allow the ice to melt off of the evaporator. 2 Remove all ice from the storage bin. 3 Remove inside front cover (see Figure 33). Never use anything to force ice from the evaporator. Damage may result. Figure 33 FRONT COVER 28 1 Set the cycle selector switch to OFF and allow the ice to melt off of the evaporator. 2 Remove all ice from the storage bin. 3 Remove inside front cover (see Figure 33). Never use anything to force ice from the evaporator. Damage may result. Figure 33 FRONT COVER Maintenance Self Cleaning — Every 6 Months To maintain operational efficiency, clean the unit every six months (depending on water conditions more or less frequent cleaning may be necessary). If the ice maker requires more frequent cleaning, consult a qualified plumber to test the water quality and recommend appropriate treatment. ! WARNING WARNINGWARNINGWARNINGWARNINGWARNING Wear rubber gloves and safety goggles and/or face shield when handling Ice Machine Cleaner. ! CA CACACACACAUTION UTIONUTIONUTIONUTIONUTION Use only Electrolux Ice Machine Cleaner (part number EIM30046). It is a violation of Federal law to use this solution in a manner inconsistent with its labeling. Use of any other cleaner can ruin the finish of the evaporator and will void the warranty. Read and understand all labels printed on the package before use. Ice machine cleaner is used to remove lime scale and other mineral deposits. Refer to the following steps for mineral deposit removal. ! CA CACACACACAUTION UTIONUTIONUTIONUTIONUTION 29 Figure 34 Maintenance 4 Remove the overflow tube by lifting it up while using a slight back and forth motion to loosen it from the drain hole (see Figure 34). The water in the reservoir will flow down the drain. 5 Replace the overflow tube after all of the water has drained from the reservoir. 6 Move the cycle selector switch to the CLN position. 7 When water begins to flow over the evaporator (approximately 3 minutes), add one package of Electrolux Ice Machine Cleaner to the water reservoir. 8 Reinstall inside front cover. 9 When the self-cleaning process stops (approximately 45 minutes) it may be desirable to clean the storage bin at this time (see Interior Cleaning). 10 Move the cycle selector switch to the ICE/ON position to resume ice production. Inlet Screen Cleaning — Every Year The solenoid valve inlet screen must be cleaned at least once each year as follows: 1 Shut off the water at the water supply valve. 2 Pull the unit out to access the back panel (see Figure 35). 3 Disconnect electrical power to the unit. 4 Disconnect the entire hose connector from the water solenoid valve (see Figure 35). 5 Use a tooth brush to clean sediment from the inlet screen. DO NOT remove the screen. 6 Re-connect the water supply line to the water solenoid valve. Tighten connector securely. Open the water supply valve and check for leakage at the water connection. Make sure the water supply line is not kinked. 7 Reconnect power to the unit before re-installing. 8 Make sure the drain system is working properly and the drain hose is not pinched or kinked. Pour one gallon of cool, fresh water into the ice bin. The water should drain freely. If your ice maker is equipped with a drain pump, the pump should drain the ice bin. UL209a OVERFLOW UL103_CO WATER CONNECTION Figure 35 29 Figure 34 Maintenance 4 Remove the overflow tube by lifting it up while using a slight back and forth motion to loosen it from the drain hole (see Figure 34). The water in the reservoir will flow down the drain. 5 Replace the overflow tube after all of the water has drained from the reservoir. 6 Move the cycle selector switch to the CLN position. 7 When water begins to flow over the evaporator (approximately 3 minutes), add one package of Electrolux Ice Machine Cleaner to the water reservoir. 8 Reinstall inside front cover. 9 When the self-cleaning process stops (approximately 45 minutes) it may be desirable to clean the storage bin at this time (see Interior Cleaning). 10 Move the cycle selector switch to the ICE/ON position to resume ice production. Inlet Screen Cleaning — Every Year The solenoid valve inlet screen must be cleaned at least once each year as follows: 1 Shut off the water at the water supply valve. 2 Pull the unit out to access the back panel (see Figure 35). 3 Disconnect electrical power to the unit. 4 Disconnect the entire hose connector from the water solenoid valve (see Figure 35). 5 Use a tooth brush to clean sediment from the inlet screen. DO NOT remove the screen. 6 Re-connect the water supply line to the water solenoid valve. Tighten connector securely. Op...


Scrivi la tua opinione del dispositivo



Il messaggio
Il tuo nome :
Inserire le due cifre :
capcha





categorie