Log:
valutazioni - 3, GPA: 3.7 ( )

Istruzioni per l'uso Fisher-Price, Modello BUBBLE MOWER H8910

Produttore : Fisher-Price
File Size : 270.68 kb
File Nome : H8910pr-0920.pdf
Lingua di insegnamento: en
Vai a scaricare



Facilità d'uso


No tools needed for assembly. H8910 Instructions Please keep this instruction sheet for future reference, as it contains important information. Adult assembly is required. No tools needed for assembly. IMPORTANT! IMPORTANT! • Please make sure your child does not follow you using this toy while you are operating a real lawn mower. Your child should play in a separate area away from the area where you mow. • Use only bubble solution in this toy. • Make sure your child understands that bubble solution is not for drinking and that it should be kept away from the eyes. • While filling or cleaning this toy, try to avoid spilling bubble solution on the floor. It may create slippery floor conditions. Assembly • Insert and "snap" the handle into the mower, as shown. 2 Bubblin’ Fun PRESS11 13 Bubblin’ Fun PRESS11 13 • Remove and discard the cap and seal • Press down on the bottle for about from the bubble solution bottle. 15 seconds to fill the mower. • Carefully fit the bottle to the bottom of the filler cap attached to the front of the mower. Twist the bottle to attach. 12 • Insert the bottle, cap side down, into the opening near the front of the mower. Fisher-Price, Inc., a subsidiary of Mattel, Inc., East Aurora, NY 14052 U.S.A. ©2005 Mattel, Inc. All Rights Reserved. ® and ™ designate U.S. trademarks of Mattel, Inc. PRINTED IN MEXICO H8910pr-0920 3 • If your mower still does not make bubbles: -Check to be sure there is enough bubble solution in the mower. -Make sure all four wheels contact the ground when pushing the mower. -Empty bubble solution from the mower. Wash the bubble chamber and filler opening. Refill with fresh bubble solution (see page 5). Note: We do not recommend the use of silicones or oily lubricants on this toy. As with any bubble producing toy, when even a very small amount of silicone or oily lubricants are put into or used near the bubble chambers, bubbles will not form. Bubblin’ Fun • Push the bubble mower so that all four wheels contact the ground. • Bubbles begin flowing after the mower has been pushed about 15-20 walking steps. As long as the mower is being pushed, bubbles continue to flow. • When bubbles stop, press down on the bubble bottle again for 15 seconds to refill. 4 Let’s Clean Up 11 13 Let’s Clean Up 11 13 • Lift to remove the bubble solution • Tip the mower forward to empty all bottle from the mower. Twist to the water. remove the filler cap. Set the bottle RINSEHERERINSEHERE12 • Thoroughly rinse the bubble chamber on the side of the mower and filler opening near the front of the mower with clean water from a garden hose or faucet. Cap End Up For Storage 14 • Replace the filler cap on the bubble solution bottle and place the bottle in the filler opening cap end up. Hint: Please keep the bubble solution bottle with your toy and refill as necessary. 5 Consumer Information Problems and Solutions Problem Cause Solution No bubbles Not enough bubble solution in bubble chamber Press down on bubble solution bottle for 15 seconds to refill. Bubble chamber is clogged and dirty Follow instructions in “Let’s Clean Up” section to clean bubble chamber thoroughly. You have not walked far enough to produce bubbles The bubble mower needs to be pushed a minimum of 15-20 walking steps before bubbles begin to flow. You are walking too quickly Walk at a slow, steady pace. The rear wheels do not contact the ground Push the mower so that the rear wheels always contact the ground. Silicone or oily lubricants may have gotten in the bubble chamber Never use silicone or oily lubricants on this product (the wheels). Bubbles will not form if even a very small amount of these substances get into the bubble chamber. Bubble solution is leaking from the mower Bubble chamber over-filled Fill only by using filler cap. The filler cap dispenses the correct amount of solution. The mower is used on an inclined surface Use the mower only on flat, level ground. Bubble solution is foaming Bubble chamber is clogged Follow instructions in "Let's Clean Up" section to clean bubble chamber thoroughly. Consumer Information Problems and Solutions Problem Cause Solution No bubbles Not enough bubble solution in bubble chamber Press down on bubble solution bottle for 15 seconds to refill. Bubble chamber is clogged and dirty Follow instructions in “Let’s Clean Up” section to clean bubble chamber thoroughly. You have not walked far enough to produce bubbles The bubble mower needs to be pushed a minimum of 15-20 walking steps before bubbles begin to flow. You are walking too quickly Walk at a slow, steady pace. The rear wheels do not contact the ground Push the mower so that the rear wheels always contact the ground. Silicone or oily lubricants may have gotten in the bubble chamber Never use silicone or oily lubricants on this product (the wheels). Bubbles will not form if even a very small amount of these substances get into the bubble chamber. Bubble solution is leaking from the mower B...


Scrivi la tua opinione del dispositivo



Il messaggio
Il tuo nome :
Inserire le due cifre :
capcha





categorie