valutazioni - , GPA:
(
)
)
Produttore : Harbor Freight Tools
File Size : 4.67 mb
File Nome : 92050.pdf
Lingua di insegnamento: 
Il documento viene caricato, si prega di attendere
 |
Il documento viene caricato, si prega di attendere
Facilità d'uso
Check for any broken or damaged parts and any other conditions that may affect its operation. Replace or repair damaged or worn parts immediately. 6. Replacement parts and accessories. When servicing, use only identical replacement parts. Use of any other parts will void the warranty. 7. Do not operate product if under the influence of alcohol or drugs. Read warning labels on prescriptions to determine if your judgment or reflexes are impaired while taking drugs. If there is any doubt, do not operate the product. 8. Use eye protection. During assembly, always wear ANSI approved impact safety goggles. SKU 92050 For technical questions please call 1-800-444-3353. Page 2 9. Wear gloves and avoid sharp edges when assembling. 10. Make certain that the Greenhouse is placed on a falt, level, solid surface capable of supporting the Greenhouse. 11. Because of aluminum dust, be certain to wash your hands after handling the Greenhouse. 12. Never allow children to play with this product. Caution: Small parts can be easily swallowed by small children. WARNING: This product contains or, when used, produces a chemical known to the State of California to cause cancer and birth defects or other reproductive harm. (California Health & Safety Code 25249.5, et seq.) Warning: The warnings, cautions, and instructions discussed in this instruction manual cannot cover all possible conditions and situations that may occur. It must be understood by the operator that common sense and caution are factors which cannot be built into this product, but must be supplied by the operator. Unpacking When unpacking your Miniature Greenhouse, check to make sure the following parts are included. If any parts are missing or broken, please call HARBOR FREIGHT TOOLS at 1-800-444-3353. Assembly/ Operation Your Miniature Greenhouse will require complete assembly prior to use. It is important that you read the entire manual to become familiar with the product BEFORE you assemble and use the Greenhouse. Before assembling and operating the Greenhouse be sure that you have all parts described in the Parts List and Assembly Diagram located on the last pages of this manual. Note that throughout the assembly process all parts of the Greenhouse frame will be attached using the Bolts and Nuts (11) provided. Parts have been labeled with the appropriate part number to help with assembly. Refer to the assembly diagrams and figures for all steps. Do not install Windows until specified in the assembly directions. 1. Attach Back (1) to both Sides (2). Make certain that all sides are square and that edges overlap appropriately. Insert Bolts (11) through each hole in the corner and thread on Nuts (11)-see Figure 1 and assembly diagrams. Figure 1-Attaching 1 to 2 Bolts and Nuts (11) SKU 92050 For technical questions please call 1-800-444-3353. Page 3 2. Attach Front (3) to both Sides (2). Make certain that all sides are square and that edges overlap appropriately. Insert Bolts (11) through each hole in the corner and thread on Nuts (11)-see assembly diagrams. 3. Connect Rear (1), both Sides (2) and Front (3) (as assembled in steps 1 and 2) to Top Frame (8)- see Figure 2. Connect (8) to (1), (2) and (3) with Bolts and Nuts (11). (8) Figure 2-Part (8) to Top 4. When attaching the Top Frame (8), make certain that the bolt holes at the end of the Top Frame (8) line up underneath the bolt holes of the Rear (1) and Front (3). Make certain that the Bolts (11) are inserted from the outside. 5. Set the Cross-Beams (9) so that there are three on each side of the Greenhouse. Line them up with the corresponding holes-see Figure 3 and the Assembly Diagram. Figure 3-Part 10 to Cross-beam (9) 9 9 (10) 6. Attach the Window Lower Support (10) to the Center Cross-Beam (9) as shown in Figure 3. Use Nut and Bolt (11) to secure in place. The square head of the Bolt (11) will slide into place - see Figure 3. 7. Attach Window (7) to Top Frame (8). Set the Plastic Panel (7) so that it is supported by the Panel Lower Support (10) and the Top Frame (8). Test to make certain that the Small Plastic Panel (7) moves smoothly and adjusts with no problems. Before assembling the plastic panels, remove the protective plastic covering from each one. 8. Place all of the plastic Side Panels (4) into the spaces on both walls of the Greenhouse. Set the Metal Holding Clip (12) on each side to hold the plastic Side Panels in place-see Figure 4. 9. Place seven Roof Panels (5) along the top of the Greenhouse. Place the smaller Top Roof Panel (6) into space on top of the Greenhouse (below Window (7). Use the Metal Holding Clip (12) on each side to hold each plastic panel in place- see Figure 4. SKU 92050 For technical questions please call 1-800-444-3353. Page 4 Figure 4-Inserting Plastic Panels Metal Holding Clip (12) Figure 4-Inserting Plastic Panels Metal Holding Clip (12) 1. To clean, wipe with a damp cloth, using a mild detergent. Do not use cleaners that are combustible or corrosive. Dry with a clean, non...