valutazioni - 2, GPA: 4
(
)
)
|
Facilità d'uso
Turn the handle back (counter-clockwise) to turn the cold water off. Turn the hot handle forward (counter-clockwise) to turn the hot water on. Turn the hot handle back (clockwise) to turn the hot water off. Technical Data Recommended hole size spout 1 3/8“ valves 1 1/4“ Maximum depth of mounting surface 1 1/8“ Flow rate @ 45 psi 2.2 gpm Maximum water pressure 145 psi Recommended water pressure: 14.5 - 75 psi Recommended hot water temp.: 120oF - 140oF* *Some municipalities limit the maximum water temperature from the water heater to 120o or below. Please know and follow all applicable local codes when setting the temperature on the water heater. Prepare to install the faucet: Prior to installation, install the supply stops. Hot and cold supply lines and nuts are not included with the faucet. They must be purchased separately by the plumber or by the consumer. Flush the supply lines thoroughly. Damage to the faucet caused by debris in the water line is not covered under the limited lifetime warranty. Assembly • Install the valves to the lavatory. • Install the valve mounting screws, but do not tighten them. • Install the spout to the handle assembly. Use a 5 mm allen wrench to install and tighten the spout retaining screws. • Place the spout and handle assembly over the valve bodies. Tighten the valve mounting screws. • Install the drain pull rod. Place the spout mounting piece and the nut over the threaded shank on the bottom of the spout assembly. Tighten the nut. • Place a compression nut and ferrule over the spout tube. • Install the mounting angle. Tighten the compression nut by hand, then finish tightening with a wrench. • Screw the hot and cold connection hoses to the mounting angle. • Place a compression nut and washer over the shank end of one of the connection hoses. • Attach the hose to the outlet port on the valve with the compression fitting. Tighten with a wrench. Repeat with the other connection hose. • Install the supply hoses (not included) and connect them to the stops. • After the drain is installed, turn on the water and check all connections for leaks. Install the pop-up drain Remove the plunger assembly. Unscrew the drain outlet flange from the tee. Unscrew the tailpiece from the tee. Wrap the threads with plumbers’ thread tape and replace. Install the white, flexible sealing gasket to the flange. Place it in the sink outlet. From under the sink, install the black mack gasket, white friction ring and retainer nut to the flange. Do not tighten the nut against the bottom of the sink at this time. Thread the tee and tailpiece to the flange. The pivot must face the faucet. If necessary, turn the drain assembly. Tighten the retainer nut. Place the plunger assembly in the drain. Install the horizontal rod so that the end goes through the loop in the bottom of the height adjuster. Install and hand tighten the pivot ball nut. Attach the swivel connector to the end of the horizontal rod. Attach the swivel connector to the end of the pull rod. Position as desired and tighten with a small, flathead screwdriver. plunger height adjuster flange sealing gasket mack gasket friction ring pull rod retainer nut tee pivot ball nut horizontal rod swivel connector Replacement Parts 1 handle 39293XX0 2 cold escutcheon 96679XX0 3 hot escutcheon 96678XX0 4 escutcheon 96680XX0 5 cold cartridge 94008000 6 hot cartridge 94009000 7 aerator - lavatory 96673000 8 aerator - bidet 94005XX0 9 bidet swivel 96050XX0 10 spout - lavatory 5 1/2” 96674XX0 11 spout - bidet 96675XX0 12 pull rod 96676XX0 13 spout mounting kit 96016000 XX = Color code 00 chrome plated 82 brushed nickel Cleaning Recommendation for Hansgrohe Products Modern faucetry and shower products utilize a combination of materials to comply with the needs of the market with regard to design and functionality. To avoid damage, it is necessary to use some caution when cleaning. Damage caused by improper treatment is not covered under the Hansgrohe warranty. Cleaning Materials for Faucets and Showers • To remove lime scale, use only products made specifically for that purpose. Always follow the manufacturer’s instructions when using. • Do not use cleaners that contain hydrochloric, formic, acetic, or phosphoric acids, as these will cause considerable damage to finishes and to plastic components. • Never mix cleaning materials. • Never use cleaners containing abrasives. Do not use abrasive cleaning cloths, pads, or sponges. Cleaning Procedures • Clean your faucets and shower products as and when required. Regular cleaning will prevent scale buildup and water spotting. • Follow the label instructions. Do not allow any cleaner to remain on the product for longer than necessary. • When using spray cleaners, spray first onto a sponge or cloth – do not spray directly onto the product. • After cleaning, rinse thoroughly with clear water to remove any cleaner residu...
Questo manuale è adatto anche per i modelli :Altri accessori per la casa - Citterio 39136XX1 (583.03 kb)