Log:
valutazioni - 4, GPA: 4.3 ( )

Istruzioni per l'uso American Standard, Modello 2461.XXXW Series

Produttore : American Standard
File Size : 1023.05 kb
File Nome :
Lingua di insegnamento: en
Vai a scaricare



Facilità d'uso


NO SUPPORT UNDER THE SUMP IS NECESSARY. POSITION BATHTUB/WHIRLPOOL WITHIN THE RECESS, CHECK LEVEL, FRONT TO BACK, SIDE TO SIDE, AND SHIM AS NECESSARY. ALSO CHECK DRAIN CLEARANCE HOLE IN THE SUBFLOOR. TO SECURE THE TUB TO WOOD STUDS USE ROOFING NAILS IMMEDIATELY ABOVE THE FLANGE OF THE TUB. TO SECURE THE TUB TO STEEL STUDS USE DRYWALL SCREWS AND FLATWASHERS. CAUTION: TAKE EXTRA CARE WHEN DRIVING NAILS OR SCREWS TO AVOID DAMAGING THE TUB. THE TILE OR SIMILAR FINISHED FLOOR WILL BE BUTTED AGAINST THE BOTTOM OF THE TUB APRON, ALSO HOLDING THE TUB IN PLACE. TYPICAL RECESS INSTALLATION 610 mm (24) 305mm (12) 441mm (17-3/8) 1527mm (60-1/8) 229 X 305mm (9 X 12) FLOOR CUTOUT 813mm(32)TUB WIDTH SUGGESTED WHIRLPOOL/BATH INSTALLATION METHOD SECURE THE BATH TO THE STUDS AS SHOWN FOR WOOD OR STEEL STUD CONSTRUCTION. STUD SHIM DRY WALL TILE SEALANT TUB ROOFING NAIL 51 x 102mm (2 x 4) WOOD STRINGER FULL LENGTH 51 x 102mm (2 x 4) WOOD STRINGER FULL LENGTH STEEL STUD SHIM DRY WALL WASHER TILE SEALANT TUB 4" (102mm) DRYWALL SCREW WOOD STUDS STEEL STUDS WHIRLPOOL ONLY: UNLESS AN ACCESS OPENING OF AT LEAST 12" X 24" (305 X 610MM) IS PROVIDED, WARRANTY SERVICE WILL NOT BE PERFORMED. 791033-100 Rev. I (2) ELECTRICAL INSTALLATION INSTRUCTIONS All wiring must be performed by a licensed electrician in accordance with the national electrical code and all other applicable codes. WARNING: When using electrical products, basic precautions should always be observed, including the following: 1. DANGER: RISK OF ELECTRIC SHOCK Connect only to a circuit protected by a ground-fault circuit interrupter. 2. Grounding is required. The unit should be installed by a licensed electrician and grounded. 3. Install to permit access for servicing. 4. All building materials and wiring should be routed away from the pump body and heater (if equipped). The whirlpool should be installed on a 120 vac, 15 amp dedicated circuit. The circuit should be hard-wired from the electrical power supply panel. The circuit must be a three (3) wire circuit from the electrical supply panel. A grounded neutral wire and a third wire, earth ground, are essential. ADDING THE SAFE-T-HEATER REQUIRES A SEPARATE 15 AMP MAXIMUM GFCI CIRCUIT. ELECTRICAL DIAGRAM READ AND FOLLOW ALL INSTRUCTIONS BLACKWHITE 120 VAC GND. SEPARATE 15 AMP GFCI OUTLET WHIRLPOOL MOUNTED AIR SWITCH or WALL TIMER ELECTRICAL INSTALLATION PUMP/MOTOR 791033-100 Rev. I (3) WIRE SELECTION GUIDE Motor Hi-Performance Rating 1.6 Maximum distance from fusebox to motor 50' 100' 150' 200' 120V Power Line 12 12 10 8 The sizes shown on this chart are recommendations for copper conductors only. Always follow local and national electrical codes DRAIN CONNECTION AND SYSTEM TEST Using recommended drain opening, connect whirlpool drain to waste line. Tighten all drain joints securely. Check the pump couplings and make sure they are hand-tight. Clean the whirlpool and fill with water to a point 2" above the top of the highest jet. Recheck the pump couplings and make certain that they are not leaking. (Although the pump couplings are factory tightened and inspected, some loosening may have occured during transit.) Make sure the whirlpool is connected to the electrical supply and turn the whirlpool on. Check for leaks around all piping connections while the whirlpool is running. POST INSTALLATION CLEAN-UP Remove all construction debris from bath. Tile grout can be removed with a wooden popsicle stick or tongue depressor. Do not use wire brushes or any other metal implement on bath surface. Post installation clean-up generally can be completed using warm water and liquid dishwashing detergent. Stubborn dirt or stains may be removed using granular Spic and Span® mixed with water. Painter's naphtha can be used to remove excess adhesives and/or wet oil-base paint. HARSH CHEMICALS SHOULD NEVER BE USED ON ENAMEL SURFACES. Abrasive cleaners must not be used since they will scratch and dull the surface. Dulled areas can be restored by rubbing with a white automotive-type polishing compound and waxing with a liquid wax. (4) SPIC AND SPAN® IS A REGISTERED TRADEMARK OF PROCTER & GAMBLE 791033-100 Rev. I ...

Questo manuale è adatto anche per i modelli :
Altri accessori per la casa - 2460.XXXW Series (1023.05 kb)

Scrivi la tua opinione del dispositivo



Il messaggio
Il tuo nome :
Inserire le due cifre :
capcha





categorie