valutazioni - 3, GPA: 4
(
)
)
|
Facilità d'uso
C 9b 10 A DJUSTMENTS a. Adjust water level. Water level should be adjusted to level indicated in tank by adjusting float cup. See Step 11 for water level adjustment method. IMPORTANT: b. If bowl fails to siphon, an adjustment may be required with the lift chain. Simply remove the bead chain from the retainment clip (see Fig. 10A) and take up slack on the chain, and reinsert on lift rod. Make sure the chain is not too taught. With correct washers in place (see Step 9a), tighten COUPLING NUT 1/4 turn beyond hand tight. DO NOT OVERTIGHTEN. 11 1. Turn off water supply and flush toilet to empty tank. 2. Disconnect chain from trip lever by removing hair pin cotter and clevis pin. 3. Parially lift and support piston bottom with one hand. 4. Remove thumbscrew by turning counter-clockwise. 5. Remove piston top and gasket. 6. Replace gasket with new gasket. 7. Reverse procedure, turn thumbscrew until 2 clicks are felt. TROUBLE SHOOTING FLUSH VALVE SEAL REPLACEMENT: NOTE: DO NOT ADD ANY FOREIGN MATERIALS TO THE SEALING SURFACE. 13 13a REFILL TUBE REPLACEMENT: 12 When cleaning your toilet, wash it with mild, soapy water, rinse thoroughly with clear water and dry with a soft cloth. WARNING: Do not use in-tank cleaners. These products can seriously damage fittings in the tank. This damage can cause leakage and property damage. American Standard shall not be responsible or liable for any damage caused by the use of in-tank cleaners. CARE AND CLEANING ! Turn on water supply. Submerge the FLOAT CUP under the water for 30 seconds. Adjust the water to desired level by turning WATER LEVEL ADJUSTMENT ROD and moving FLOAT CUP up or down. Diagram 1 TANK LEVER REFILL TUBE TOP ARM NIPPLE PARTS FOR WATER CONNECTION (SEE STEP 9) CONE WASHER VALVE BODY THREADED SHANK SHANK WASHER COUPLING NUT (HAND TIGHT ONLY) FILL VALVE FLOAT CUP CRITICAL LEVEL MARK ("C.L.") MUST BE 1" ABOVE OVERFLOW PIPE ADJUSTABLE HEIGHT LOCK NUT Fig. 10A WATER LEVEL ADJUSTMENT ROD Locate bottom portion of hose clip to vent tube at location as shown. THUMBSCREW PISTON TOP PISTON BOTTOM GASKET HAIR PIN COTTER 7 3 0 9 4 5 - 1 0 0 R e v . C - 4 - 14 IMPORTANT: Always clear sand and rust from system. Make sure water supply is off. Remove valve TOP by lifting arm and rotating top and arm 1/8 turn counterclockwise, pressing down slightly on cap. While holding a container over the uncapped VALVE to prevent splashing, turn water supply on and off a few times. Leave water supply off. Replace TOP by engaging lugs and rotating 1/8 turn clockwise. MAKE CERTAIN TIP IS TURNED TO THE LOCKED POSITION. VALVE MAY NOT TURN ON IF TOP IS NOT FULLY TURNED TO THE LOCKED POSITION. For troubleshooting information please contact: Manufacturer's First Year Fill Valve Warranty: TROUBLESHOOTING FILL VALVE IF FILL VALVE SHUTS OFF BUT CONTINUES TO LEAK SLOWLY, repeat Step 14. IF FILL VALVE TURNS OFF AND ON DURING PERIODS OF NON-USE, it is a signal you are wasting water because: • The end of the refill tube is inserted into overflow pipe, below water level in tank. Attach refill tube to overflow pipe using "S" clip provided. • The flush valve is leaking because it's worn, dirty or misaligned (replace seal or flush valve). IF FILL VALVE WON'T TURN ON OR SHUT OFF or REFILL OF TANK WATER IS SLOW after valve has been in use for some time, Fluidmaster Model 242 Replacement Seal may be needed. © 2001 Fluidmaster, Inc. ® Registered trademark of Fluidmaster, Inc. GUARANTEE: This Fluidmaster product is guaranteed to be free from defective materials and workmanship for a period of one year. Units returned to Fluidmaster will be replaced without charge. Always use quality Fluidmaster repair parts when maintaining your Fluidmaster products. Fluidmaster shall not be responsible or liable for any damages caused by products used with Fluidmaster valves that were not manufactured by Fluidmaster, Inc. See next page for American Standard Ten-Year "Worry-Free Decade" Limited Warranty. 30800 Rancho Viejo Road San Juan Capistrano, CA 92675 (949) 728-2000 (800) 631-2011 REPAIR PARTS LIST NOTE: "XXX" represents color or trim finish options. Specify when ordering. Repair parts are determined by toilet tank number which can be found marked inside tank. PART NO. DESCRIPTION 738922-XXX0A 034783-XXX0A 738565-424-0070A 7301111-0070A 3174.002-0070A 738985-0070A 738570-1010A 738756-0070A 735115-400-XXX 072989-0070A SKYLINE CHAMPION®4 TRIP LEVER BOLT CAP KIT (INCL TWO COVERS & WASHERS) CHAMPION®4 FLUIDMASTER 400A VALVE CHAMPION®4 FLUSH VALVE SEAL KIT CHAMPION®4 FLUSH VALVE ASSEMBLY CHAMPION®4 CLEVIS PIN ASSEMBLY CHAMPION®4 PVC REFILL TUBE CHAMPION®4 TANK TO COUPLING KIT #241 SKYLINE CHAMPION®4 TANK COVER CLIP FOR REFILL TUBE LIFT ARM FIRST 7 3 0 9 4 5 - 1 0 0 R e v . C CHAMPION®4 FLUSHING SYSTEM TEN-YEAR WORRY-FREE DECADE™ LIMITED WARRANTY For this warranty to become effective, the accompanying warranty registration card and proof of purchase must be completed and returned to the address on the warranty regi...
Questo manuale è adatto anche per i modelli :Altri accessori per la casa - 2112.014 Round Front (1.72 mb)