valutazioni - 1, GPA: 5 ( )

Produttore : American Standard File Size : 63.59 kb File Nome : Lingua di insegnamento:

To ensure that your installation proceeds smoothly--please read these instructions carefully before you begin. ACRYLIC SHOWER BASE MODELS: 3232.ST, 3636.ST, 4242.ST, 4832.ST, 4834.ST, 6032.STLH, 6032.STRH, 6034.ST, 3636 NEO, 3838.NEO, 4242.NEO For alcove (.ST models) installation only: The opening dimensions should be 1/8" larger than dimensions shown. © AS America, Inc. 2008 751817-100 Rev. QFOR AFTER-SALES SERVICE CALL 1 (800) 442-1902 WEEKDAYS. CLEANING AND MAINTENANCE D C E F G H DRAIN ASSEMBLY Strainer Drain Body Shower Base Silicone Sealant Rubber Gasket Fiber Gasket Locking Nut Rubber Caulking Gasket Lift and lower base over center of drain pipe and set into place Base Flange Drywall Screw Bracket Stud Shower Base Shower Base Splash Lip Flange Bracket Tile Adhesive Waterproof Drywall Tile Stud Caulk Your American Standard shower base is designed to last indefinitely with reasonable care and maintenance. The high-gloss acrylic surface is resistant to impact and retains its luster with proper care and maintenance. An integral, slip-resistant surface is incorporated for user safety. General Cleaning: Do not use abrasive cleaners; a mixture of warm water and a mild liquid detergent is adequate for most cleaning. Strong detergents formulated for use on tile or porcelain-enamel surfaces should be avoided. Caution: Do not allow liquid detergent containers to remain on base surfaces for more than a few moments. Do not use Lestoil, Windex, Mr. Clean, Dow Disinfectant (spray or concentrate), or Lysol Basin, Tub and Tile Cleaner. Do not allow nail polish remover, dry cleaning fluid, acetone, paint remover, or other solvents to contact acrylic surface. Level Level Level base in two directions. 51x102 mm (2x4) Stud Wall Waterproof Drywall 13mm (1/2") minimum Bedding Material Area 3 mm (1/8) 127 mm (5) 51 mm (2) PVC Pipe 159mm (6-5/8) Bedding Material No Bedding Under Apron Before installing drain into the shower base, remove strainer (see Fig. C). This will be installed after shower base is in its final position. Install the drain to the shower base as shown in Fig. D. Use silicone sealant between drain body and shower base. Secure the base to the studs as shown, using the screws and the brackets provided. See Fig. G. Note: Allow the bedding material to completely harden before applying weight to the bottom of the shower base. Draw a line 6-5/8" (159mm) from the sub-floor on to the studs at each side of the opening. Using this line and a level, mark the remaining studs. (See Figs. A & B.) This will be the installed height of the shower base. Mix the low-shrink bedding material (grout, mortar, plaster, etc.). Concrete is not recommended. Apply enough bedding material to support the entire bottom of the shower base. The bedding material must not be used under the apron (front edge). 1 SHOWER BASE 3636.NEO 3838.NEO 4242.NEO 3232.ST 4834.ST 6034.ST 3636.ST 4242.ST 4832.ST 6032.STRH/LH* 5/16" ± 1/16" 3/8" ± 1/16" 5/16" ± 1/16" 3/8" ± 1/16" 1/4" ± 1/16" 1/4"...

Scarica la tua

Per scaricare, digitare 2 cifre :