valutazioni - 2, GPA: 4 ( )

Produttore : American Standard File Size : 689.58 kb File Nome : Lingua di insegnamento:

VALVE ASSEMBLY (1340.725) For Cold or Tempered Water Supply Valve assembly is same as two handle lavatory faucets. See above instructions for assembly, (1340.725 Single Valve Faucet) is for Cold or Tempered water only. 5/16'' MIN. 9 2 4 10 11 13 MOUNTING SURFACE 5 4 14 15 8 11MOUNTING SURFACE 10 COLD OR TEMPERED WATER 7 6 13 12 9 1/2" IPS FLEXIBLE SUPPLIES or 3/8" O.D. BULL-NOSE RISER COUPLING NUT 16 ... ....INSTALL HANDLES Remove INDEX BUTTON (1; 2) and loosen SET SCREW (3) with a 2.5mm hex wrench. Install HANDLES (4) onto VALVE STEM (5). Tighten SET SCREWS (3) with 2.5mm Hex Wrench. Replace INDEX BUTTONS. Red (1) in Left HANDLE (4) Blue (2) in Right HANDLE (4). 1 1 4 3 2.5mm HEX WRENCH 3 5 4 2 2 Remove HANDLE (1) by removing INDEX BUTTON (2) and SET SCREW (3) with a 2.5mm hex wrench. Pull off HANDLE (1). To increase cycle time, turn the gray PLASTIC ADJUSTING KNOB (4) clockwise. To decrease cycle time, turn the gray PLASTIC ADJUSTING KNOB (4) counter-clockwise . Replace SET SCREW (3), INDEX BUTTON (2) and HANDLE (1). Test faucet for proper operation and cycle time. TO ADJUST CYCLE TIMESERVICE 1 2 3 4 TO INCREASE CYCLE TIME ROTATE CLOCKWISE TO DECREASE CYCLE TIME ROTATE COUNTERCLOCKWISE 2.5mm HEX WRENCH Turn on water supplies and check connections for leaks. Remove AERATOR (1) with KEY (2) supplied. Operate HOT and COLD HANDLES by pressing down on HANDLES. Both Hot and Cold handles are set for approximately 8 second operating cycles. Replace AERATOR (1). TEST INSTALLED FITTING PRESS HANDLE DOWN TO OPERATE CARE INSTRUCTIONS: DO: SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH. DO NOT: CLEAN THE PRODUCT WITH SOAPS, ACID, POLISH, ABRASIVES, HARSH CLEANERS, OR A CLOTH WITH A COARSE SURFACE. Remove HANDLE (1). Refer to Step 4 for handle removal. Remove ACTUATOR ASSEMBLY (2). Remove WASHER (3). Pull out VALVE ASSEMBLY (4) and FILTER SCREEN (5). Inspect that VALVE ASSEMBLY (4), FILTER SCREEN (5) and VALVE SEAT (6) are clean and free from debris. VALVE ASSEMBLY (3) and FILTER SCREEN (5) can be cleaned with soap and water. Replace FILTER SCREEN (5) and VALVE ASSEMBLY (4). Place WASHER (3) on top of VALVE ASSEMBLY (4). Thread VALVE ACTUATOR (2) onto faucet. Torque VALVE ACTUATOR (2) to 12-15 ft. lbs (15-20 Nm). Replace HANDLE (1). 1 4 3 5 2 REMOVE REPLACE 6 ....INSTALL HANDLES Remove INDEX BUTTON (1; 2) and loosen SET SCREW (3) with a 2.5mm hex wrench. Install HANDLES (4) onto VALVE STEM (5). Tighten SET SCREWS (3) with 2.5mm Hex Wrench. Replace INDEX BUTTONS. Red (1) in Left HANDLE (4) Blue (2) in Right HANDLE (4). 1 1 4 3 2.5mm HEX WRENCH 3 5 4 2 2 Remove HANDLE (1) by removing INDEX BUTTON (2) and SET SCREW (3) with a 2.5mm hex wrench. Pull off HANDLE (1). To increase cycle time, turn the gray PLASTIC ADJUSTING KNOB (4) clockwise. To decrease cycle time, turn the gray PLASTIC ADJUSTING KNOB (4) counter-clockwise . Replace SET SCREW (3), INDEX BUTTON (2) and HANDLE (1). Test faucet for proper operation and cycle tim...

Scarica la tua

Per scaricare, digitare 2 cifre :