valutazioni - 2, GPA: 4 ( )

Produttore : Kohler File Size : 2.57 mb File Nome : Lingua di insegnamento:

Spread a 2" (51 mm) layer of cement or mortar bed material. Apply a bead of silicone sealant around the entire rim or Apply construction adhesive to the support blocks. 1019749-2-M 8 Kohler Co. 6. Cut the Pump Banding Straps IMPORTANT!ThisstepisnecessarytomakeyourKOHLERwhirlpooloperatemorequietly. Use tin snips to cut the two pump banding straps from the whirlpool pump. NOTE:Do not raise the pump higher than it was before you cut the pump banding straps. If the pump is raised too high, it will not prime properly. Make sure the rubber isolation feet are in place. To minimize whirlpool noise and vibration, be sure the pump is not in direct contact with the shipping bracket after the pump banding straps are cut. The pump control contains rubber isolation feet to reduce pump noise. 7. Install the Plumbing CAUTION:Riskofpropertydamage.Ensure a watertight seal on the whirlpool drain. Connect the drain to the trap according to the drain manufacturer’s instructions. NOTICE:An access panel will simplify future maintenance. Install the faucet valving according to the faucet manufacturer’s instructions. Do not install the faucet trim until instructed. Open the hot and cold water supplies, and check the supply connections for leakage. Run water into the whirlpool, and check the drain connections for leakage. If required, install the grip rails. Refer to the installation instructions packed with the grip rails. 8. Install the Optional Pillow -For Models Without Neckjets CAUTION:Riskofpropertydamage.Do not submerge the pillow underwater, or use as a seat cushion. Clean the whirlpool surface of any soap film or oils. Suction cups are located on the back side of the pillow. Moisten the back side of the pillow at the suction cup locations, and position the pillow in the appropriate location on the whirlpool. Press firmly at the suction cup locations with the heel of your hand. Detach the pillow by lifting it off the whirlpool surface. Pump Wiring Harness Rubber Isolation Feet Control Cut the pump banding str aps . Moisten the back of the pillow and firmly press the suction cups against the whirlpool surface. Optional Pillo w- F or Models Without Nec kjets Use tin snips to cut the two pump banding straps from the whirlpool pump. NOTE:Do not raise the pump higher than it was before you cut the pump banding straps. If the pump is raised too high, it will not prime properly. Make sure the rubber isolation feet are in place. To minimize whirlpool noise and vibration, be sure the pump is not in direct contact with the shipping bracket after the pump banding straps are cut. The pump control contains rubber isolation feet to reduce pump noise. 7. Install the Plumbing CAUTION:Riskofpropertydamage.Ensure a watertight seal on the whirlpool drain. Connect the drain to the trap according to the drain manufacturer’s instructions. NOTICE:An access panel will simplify future maintenance. Install the faucet valving according to the faucet manufacturer’s instructions. Do not install the faucet trim until instructed. Open the hot and cold water supplies, and check the supply connections for leakage. Run water into the whirlpool, and check the drain connections for leakage. If required, install the grip rails. Refer to the installation instructions packed with the grip rails. 8. Install the Optional Pillow -For Models Without Neckjets CAUTION:Riskofpropertydamage.Do not submerge the pillow underwater, or use as a seat cushion. Clean the whirlpool surface of any soap film or oils. Suction cups are located on the back side of the pillow. Moisten the back side of the pillow at the suction cup locations, and position the pillow in the appropriate location on the whirlpool. Press firmly at the suction cup locations with t...

Scarica la tua

Per scaricare, digitare 2 cifre :