valutazioni - 2, GPA: 4.5 ( )

Produttore : AeroGarden File Size : 903.37 kb File Nome : Lingua di insegnamento:

Bulbs can be ordered at or from your retailer. After replacing Grow Bulbs, press “Reset” button to restart grow bulb timer and turn off flashing light. noTe: If you store your AeroGarden 6 between uses, grow bulb timer automatically stops when Garden is unplugged. †See complete replacement instructions on next page. • Lights On/Off Use to occasionally override built-in light timer. Once pushed, lights will stay off/on until the next time built-in light timer is set to go on/off. This will not affect the timing of your light cycle, and occasional use of this feature will not harm your plants. AeroGarden6 control Panel • Remove Bio-domes When plants appear through hole in Seed Pod Label, remove Bio-Dome and discard or recycle. noTe: never remove Seed Pod Labels. • Select The number of hours lights are on and off depends on which plant type is selected. 11 Basic Reminders About Your AeroGarden (continued) Basic Reminders About Your AeroGarden (continued) Add Nutrients Replace Bulbs Raise lamp Hood (lights) As plants grow to 1-2” from lights, raise Lamp Arm one Locking Button at a time. Be sure Lamp Arm is set on the lowest Locking Button when starting your AeroGarden 6. Unplug AeroGarden 6 and remove Bowl from Base. 1Raise Lamp Arm/Lamp Hood by holding Lamp Arm & Hood with one hand, and pushing in Locking Button with the other. 2Replace Bowl on Base and plug in AeroGarden 6. 3When “Replace Bulbs” light on control Panel begins blinking after 6 months of use… • Unplug AeroGarden 6. • Remove old Grow Bulbs and carefully discard.* IMPorTAnT: To avoid burning, be sure Grow Bulbs are cool before handling. • Insert new Grow Bulbs into Lamp Hood. • Plug in AeroGarden 6 and press and release “Reset” button to restart grow bulb timer. Early Grow Bulb Replacement If you replace Grow Bulbs before “Replace Bulbs” light illuminates, be sure to restart grow bulb timer as follows: • Press and hold “Lights” button until light next to your selected plant type starts blinking – about 5 seconds. • Release “Lights” button. The plant type selected light will continue to blink for about 9 seconds. While plant light is still blinking… • Quickly press and release “Reset” button. “Replace Bulbs” light will blink once and the plant selected light will stop blinking. Replace Grow Bulbs – order bulbs at Push locking Button in *Check with local recycling authorities for light bulb recycling availability in your area. 12 Prepare For Your Next Garden Prepare For Your Next Garden cleaning Instructions for your AeroGarden Use only water and mild soap when cleaning your AeroGarden (except when Sanitizing - Step 6). Do not use abrasive cleaners or run through the dishwasher. When your garden has completed its growing cycle… Rinse Bowl and Grow Surface with tap water. Repeat. Towel dry Bowl and Grow Surface before putting them back together and setting them on Base. If Grow Bulbs have been in use more than 6 months, they should be replaced at this time (see page 12). Your AeroGarden is now ready for replanting. Unplug AeroGarden. Carefully remove Bowl and Grow Surface from Base and bring to a sink. Set Base and Lamp Hood aside. NEVER SUBMERSE BASE AND CONTROL PANEL IN WATER. Remove Grow Surface from Bowl and place on a counter near a sink. Empty contents of Bowl in sink. Remove Seed Pods and plants from Grow Surface. • Pull Seed Pods out of Grow Surface openings. • Throw away Seed Pods and plant debris (plant growth and roots). If you compost, plant debris can be composted. Sanitize AeroGarden. • Fill Bowl . full with water. • Add . cup (59ml) of chlorine bleach. • Let sit for 2 minutes. • Using sanitizing water, wipe Grow Surface and Bowl with soft cloth or sponge.* *Gloves recommended. • Scrub underside of Grow Surface with soft scrub brush to remove any tangled roots. • Empty bleach water from Bowl. 1 2 3 4 5 6 9 7 8 Plant Growth Seed Pod Roots Grow Surface 13 Water Low Add Nutrients Replace Bulbs Salad Greens Flowers Vegetables Live Plants Herbs Reset Add Nutrients If you have already grown a garden in your AeroGarden 6, please follow the instructions below to reset the nutrient timer: Prepare For Your Next Garden (continued) 14 Replanting Your AeroGarden ! Bundle cord when furnishing is not in use. • Press and hold “Reset” button until red “Add Nutrients” light blinks 3 or 4 times (about 9 seconds). • Release “Reset” button. “Add Nutrients” light will turn off. • Your AeroGarden is now reset. (In some cases you may see other lights blink as well. This is nothing to worry about.) noTe: These steps do not reset grow bulb timer. Remember to... • Replace Grow Bulbs after 6 months of use. Grow Bulbs can be ordered at or from your retailer. • Sanitize AeroGarden 6 before replanting (see page 13). • Set your Lamp Hood to lowest position when starting a new garden. Water Low Add Nutrients Replace Bulbs Salad Greens Flowers Vegetables Live Plants Herbs Reset Add Nutrients I...

Scarica la tua

Per scaricare, digitare 2 cifre :