valutazioni - 3, GPA: 4.3 ( )

Produttore : Dometic File Size : 4.12 mb File Nome : Lingua di insegnamento:

4. Flush the toilet without water. Repeat three times. (This procedure will minimize any remaining water in the macerator pump.) 5. Turn off power to the toilet (and water supply pump if flushing with sea water). 6. Close all seacocks. If system will be subjected to freezing temperatures, please follow above procedure, and then winterize system as described below. winTERiZing At the end of each season, the SeaLand macerator toilet should be winterized for storage by using potable water-safe antifreeze (if boat or vehicle will be exposed to freezing temperatures). nOTE: Use nontoxic antifreeze designated for potable water systems. (See boat or vehicle owner’s manual.) CAuTiOn: never use automotive-type antifreeze in freshwater systems. PRESSuRiZED FRESh wATER SySTEM 1. Drain potable water tank and empty holding tank. 2. Add freshwater antifreeze to potable water tank. 3. Flush potable water antifreeze and water mixture through toilet(s) and into entire system, including the waste holding tank, diverter valve connections, discharge pumps, etc. Turn off power to toilet. Each installation is different, so amounts may vary. User discretion is required to assure adequate protection. RAw wATER SySTEM Parts required: • 1-1/2-inch (38mm) ID hose, about 3-feet (1m) long • 5/8-inch (16mm) ID hose, about 3-feet (1m) long • two containers 1. Close intake and discharge seacocks. See Hazard of Flooding risks on page 3. 2. Turn off power to toilet. 3. Disconnect and drain intake hose, discharge hose, and in-line filters. 4. Connect 5/8-inch (16mm) ID hose to raw water pump intake and 1-1/2-inch (38mm) ID hose to toilet discharge. 5. Place one container under hose connected to toilet’s discharge. 6. Place hose connected to intake pump into bucket with antifreeze and pour antifreeze in other container. 7. Turn on power to toilet and flush until antifreeze is removed from toilet. 8. Disconnect power to toilet and reconnect all intake and drain hoses. 4 TROubLEShOOTing guiDE Problem Possible Cause Service instructions 1. Flush cycle operates correctly but water in the bowl empties slowly or not at all. a. Discharge piping is pinched or kinked. b. Discharge piping is too high. (Remember, all upward vertical loops and should not exceed a total of 9.8 feet (3 m) in height.) c. The macerator pump or discharge piping is blocked. a. Check discharge piping. b. Reroute discharge piping. c. Close seacocks and clear blockage. 2. Macerator pump makes unusually loud noise or continually trips breaker. a. Foreign material in pump chamber. a. Close seacocks and clear foreign material. 3. Flush cycle is not activated after pushing on flush button. a. Holding tank is full and signal from tank has shut down electrical power to toilet. b. Electrical power to toilet is shut off or disrupted. c. Flush Control Touchpad is malfunctioning. d. Circuit board in Electronic Control Module is malfunctioning. a. Empty holding tank. b. Check wiring and circuit breakers (or fuses). c. Replace touchpad. d. Replace control module. 4. Insufficient or no water enters the bowl. a. Water supply line is pinched or kinked. b. Screen in water valve is blocked. c. Intake water filters are blocked (in raw water system). d. Water valve is malfunctioning. a. Check water supply line. b. Clear blockage at water valve. c. Clear water filters. d. Replace water valve. 5. Fresh water demand pump turns on and off repeatedly during toilet operation. a. Pump cut-out pressure is too low (25 PSI or less). b. Pump GPM output exceeds water valve input. c. Water valve screen is blocked. d. Water valve is malfunctioning. a. Install an in-line water accumulator tank or upgrade the water pump. b. Install an in-line water accumulator tank. c. Clear blockage at water valve screen. d. Replace water valve. 5 DEODORAnTS AnD SPECiAL TiSSuE Your SeaLand toilet requires the regular addition of a deodorant product to reduce malodors and to help break down holding tank contents. Several factors should be considered in selecting a deodorant product. Liquid or granulated. Liquid products work more quickly by readily going into solution. Granulated powder formulations have the advantage of requiring less storage space and are less likely to leak if the package is inadvertently damaged. Formaldehyde versus non-Formaldehyde. Dometic manufactures both types of deodorants. Generally speaking, formaldehyde formulas control odor very effectively at all temperatures and with all degrees of water hardness. Both SeaLand® Environment-Friendly and Clean ‘n Green™ brands, which are formaldehyde free, are similarly effective. how Much Deodorant and how to Add it. The deodorant is added directly into the toilet bowl, then flushed into the holding tank. Follow bottle or package instructions. Conditions of extremely warm weather, longer waste holding time and larger tank capacities may require more deodorant treatment. Also, to maintain optimum efficiency in odor control, the waste holding tank should be cleaned th...

Scarica la tua

Per scaricare, digitare 2 cifre :