valutazioni - 2, GPA: 4.5
(
)
)
|
Facilità d'uso
It is the responsibility of the spa owner to provide a proper foundation for the spa. We strongly recommended that you have a qualified, licensed contractor prepare the foundation for your spa. Place the spa on a level concrete slab not less than 3” / 8 cm thick. If you are installing the spa indoors, pay close attention to the flooring beneath it. Choose flooring that will not be damaged or stained. If you are installing your spa on an elevated wood deck or other structure, consult a structural engineer or a contractor to ensure the structure will support the weight of 150 pounds per square foot. Electrical Installation This product is a cord-connected spa with a pump heater, lighting fixture, and spa side control. The operating power is 110V AC. A licensed electrician may be required to upgrade your standard receptacle and/or circuit breaker. Always follow applicable local, state and federal codes and guidelines. The spa is equipped with a 15 amp GFCI cord and plug kit. Plug the spa into a dedicated electrical line with a 15 amp breaker. Always use a weatherproof-covered receptacle. Receptacle shall be located not less than 5 feet (1.5 m) from and not exceeding 10 feet (3.0 m) from the inside wall of the spa (NEC 680.43(A)). Do not use extension cords. Using an extension cord will void your warranty. Do not bury the power cord. If your cord becomes damaged, replace it before next usage. If you need to replace your cord, replace it with a 15 amp GFCI connection. The cord may not be longer than 15 feet (4.6 m). Testing the GFCI Test the GFCI plug prior to first use and periodically when the spa is powered. To test the GFCI plug version, follow these instructions. (Spa should already be plugged in and operational.) Press the TEST button on the GFCI. The GFCI 1. will trip and the spa will stop operating. Press the RESET button on the GFCI. The GFCI 2. will reset and the spa will turn back on. The spa is now safe to use. If the GFCI trips while the spa is in use, press the RESET button. If the GFCI does not reset, unplug the spa and call your local Cal Spas dealer for service. DO NOT USE THE SPA! Filling and Powering Up Your Portable Spa Never fill your spa with soft water. Soft water makes it impossible to maintain the proper water chemistry and may cause the water to foam, which will ultimately harm the finish of the spa and void your warranty. Once the spa has been placed on an approved 1. surface and has been correctly wired by a licensed electrician, inspect all plumbing connections in the equipment area of your spa. Ensure that these connections are secure and that they did not loosen during shipment. If equipped, open all gate valves in the equipment 2. area. Before operating the spa, these valves must be in the up or “open” position. VERY IMPORTANT! Never run the spa with the gate valves closed or without water circulating for long periods of time. Be careful not to over-tighten the plumbing fittings. Remove the cartridge from filter canister.3. Place a garden hose in the filter canister and fill 4. your spa with regular tap water about six inches from the top. VERY IMPORTANT! Always fill the spa through the filter canister! Failure to do so may cause air to be trapped in the filtration system and prevent the pumps from operating properly. Presoak the filters in spa water.5. VERY IMPORTANT! You must presoak the filters before inserting them in the filter canister. Dry filters can allow air into the filtration system which can cause pump failure. Once the water is at the correct level and air is 6. bled, plug in the spa into a dedicated electrical outlet. Note: When the power is turned on to the spa, the controls will perform a diagnostic check for approximately five minutes. When the diagnostic is complete, the spa will automatically operate at filter speed and continue heating until the spa water temperature reaches the default temperature of 100.F. If no water is flowing when the pump is running, 8. there could be an air pocket at the suction side of the pump. Shut off power to the spa and loosen the pump union on the suction side of the pump to bleed the air. When air is bled, turn power back on. Install the pre-soaked filters into the filter canis9. ter. The spa is now ready for use. Operating Your Spa Electronic Control Operation Initial Start up When first powered up, your spa will perform a self-diagnostic check and go into priming mode. When the control panel displays PR, IMMEDIATELY do the following: Press the JETS button to turn on the 1. pump and let it run for 10 seconds. The pump should be running in low speed. Press the JETS buttons again and let the 2. pump run in high speed for 10 seconds. Press the JETS button again to turn off the pump. 3. The pump should be left in the off position for 10 to 15 seconds. Repeat steps 1 through 3 until water is flowing 4. through all the jets and all air is removed from the plumbing. When the spa has finished priming, the heater will be activated and t...