valutazioni - 4, GPA: 4
(
)
)
|
Facilità d'uso
It can also be operated while standing on the floor. Keep a safety distance of 0.5 m towards any easy inflammable materials (decoration etc.). Install a safety wire that can hold at least 10 times the weight of the fixture. Never use the carrying handles for secondary attachment. Pay attention to the regulations of: BGV C1 (former VBG 70) and DIN VDE 0711-217 ! The installation should be done by qualified staff only. 2.1.1 Clamps There are two major possibilities to mount the POWER WASH 575E together with clamps. Camlock system or direct mounting of clamps. In both cases you have to regard a sufficient stability of the system. For installation instructions please see also printing on the backside of the case. 90° b) Use two clamps direct on the backside of the POWER POWERPOWER WASH WASHWASH 575E 575E575E to mount the unit on a truss (each two opposite threads max. M10x20). 4x M10x20mm 4x Camlock 2.2 Secure the POWER POWERPOWER WASH WASHWASH 575E 575E575E Regardless of the rigging of the POWER POWERPOWER WASH WASHWASH 575E 575E575E you have to use a stipulated safety wire. Therefore you have to thread to safety wire through to two provided holes on the backside of the fixture and connect it with the truss- support. Pay attention to a safe and proper fastening. Elation Lighting Connections 2.3.1 Power supply Electronic ballast with: ~90 - 260 Volt, 50 - 60 Hz, earth contact type plug - Powercon Connected load 780W <=> 3.8 A (blind current compensation). Please see printing on the case for the right electronic supply! 2.3.2 DMX DMX 512 Standard input/output. See also printing on the case for the right pin assignment. [+] = Pin 3 / [-] = Pin 2 / [Ground] = Pin 1 The DMX-Addressing starts at the DMX-Address [001]. 2.4 Fuse The POWER POWERPOWER WASH WASHWASH 575E 575E575E electronic system is protected by two 5x20 mm fine- wire fuses. Lamp: 230V / T 5A Electronic: 230V / T 1A Please see the printing on the POWER POWERPOWER WASH WASHWASH 575E 575E575E casing for more details. Attention: • Disconnect AC outlet before changing a fuse! • Use only the original declared fuse type! Elation Lighting 3 The Menu Field You’ll find the control board on the side part of the base. It allows you to make all necessary adjustments of the POWERPOWER WASHWASH 575E.575E. With the Mode-key you get into the main menu. Afterwards you can navigate through the menu with the Up/Down-keys. Push the Enter-key to get in the next menu level or to confirm your settings. Make them and set functions ON/OFF with the Up/Down-keys. Confirm and save it with the Enter-key (the display shows OK). Push the Mode-key to cancel the entry and go back to the main menu. M DEE RD N MODE ENTER UPDOWN UPMODE ENTER DOWN Display Level 1 Level 2 Level 3 Remark Define the DMX start address Test program of all functions Self-running audio program (slow) Self-running audio program (fast) Master for the audio program Basic position for the audio program Size for the audio program (NORM-BIG-MIDL-SMAL) Switch on/of the lamp direct at the POWERPOWER WASHWASH 575E575E Reset Running time of the fixture (no destructible) Running time of the lamp (erasable) Running time of the lamp (no destructible) Reverse Pan-direction Reverse Tilt-direction Manual drive of all device functions Automatic lamp start Switch off lamp via DMX Reed out actual DMX-values Display On/Off Twist the display D001 TEST AUDI ASLW AFST MSTR SVPT SIZE LAMP RESE TIME POWR LA1 LA2 FCOL RPAN RTLT SPEC MANU LAAU DLOF DMXI DISP D ON REV TEMP FANS HIGH REG LOOF LOHI fl DOWN - UP ‡ ADJU CODE xxxx CYAN MAGE YELL COLO BSPR Reed out internal temperature Maximum cooling fan velocity Automatic cooling fan control Low cooling fan speed ‡lamp off Low cooling fan speed ‡automatic Define the DMX start address Use the code for entering the calibration menu (for authorized persons only) Calibration of the Cyan color wheel Calibration of the Magenta color wheel Calibration of the Yellow color wheel Calibration of the color wheel Calibration of the beam shape 3 The Menu Field You’ll find the control board on the side part of the base. It allows you to make all necessary adjustments of the POWERPOWER WASHWASH 575E.575E. With the Mode-key you get into the main menu. Afterwards you can navigate through the menu with the Up/Down-keys. Push the Enter-key to get in the next menu level or to confirm your settings. Make them and set functions ON/OFF with the Up/Down-keys. Confirm and save it with the Enter-key (the display shows OK). Push the Mode-key to cancel the entry and go back to the main menu. M DEE RD N MODE ENTER UPDOWN UPMODE ENTER DOWN Display Level 1 Level 2 Level 3 Remark Define the DMX start address Test program of all functions Self-running audio program (slow) Self-running audio program (fast) Master for the audio program Basic position for the audio program Size for the audio program (NORM-BIG-MIDL-SMAL) Switch on/of the lamp direct at the POWERPOWER WASHWASH 575E575E...