valutazioni - 2, GPA: 4 ( )

Produttore : DeWalt File Size : 674.71 kb File Nome : b3004541-6976-4dc6-9c13-3f6947a29b69.pdf Lingua di insegnamento:

9. To stop the tool, release the trigger switch. Always turn the tool off when work is finished and before unplugging. DRILLING WITH A CORE BIT CAUTION: Do not use a core bit for drilling wood. Personal injury and damage to tool may result. 1. Set the model selector to hammerdrilling mode. 2. Move the torque control lever to Setting 2 (R). 3. Turn the speed and impact control dial to the maximum torque position. 4. Adjust the side handle (front or rear position). 5. Assemble the centering bit and adapter shank into core bit. 6. Mark the spot where the hole is to be drilled. 7. Place the centering bit on that mark and depress the trigger switch. NOTE: Some core drills require the removal of centering bit after about 1cm of penetration. If so, remove and continue drilling. 8. When drilling through a structure thicker than the depth of the core bit, break away the round cylinder of concrete or core inside the bit at regular intervals. To avoid unwanted breaking away of concrete around the hole, first drill a hole the diameter of the centering bit completely through the structure. Then drill the cored hole halfway from each side of the structure. 9. To stop the tool, release the trigger switch. Always turn the tool off when work is finished and before unplugging. Chipping and Chiseling (D25701, D25730, D25890) 1. Set the model selector to chipping mode. 2. Set the impact control dial to desired setting (refer to Electronic Speed and Impact Control ). 3. Insert the appropriate chisel and rotate it by hand to lock it into the desired position. NOTE: For SDS max models, only use SDS max insert tools. 4. Adjust the side handle (front or rear position). 5. Depress the trigger switch. 6. Apply only enough pressure to engage active vibration control (refer to Active Vibration Control ). 7. To stop the tool, release the trigger switch. Always turn the tool off when work is finished and before unplugging. MAINTENANCE Cleaning CAUTION: Never use solvents or other harsh chemicals for cleaning the non-metallic parts of the tool. These chemicals may weaken the plastic materials used in these parts. Use a cloth dampened only with water and mild soap. Accessories Recommended accessories for use with your tool are available at extra cost from your local dealer or authorized service center. If you need assistance in locating any accessory, please contact DEWALT Industrial Tool Co., 701 East Joppa Road, Baltimore, MD 21286, call 1-800-4-D EWALT (1-800-433-9258) or visit our website CAUTION: The use of any other accessory not recommended for use with this tool could be hazardous. MAXIMUM CAPACITY D25701 D25730 D25890 Concrete 1-7/8" (48mm) 2" (52mm) –– RPM 137-275 125-250 –– No load BPM 1260-2520 1 150-2300 1 150-2300 Repairs To assure product SAFETY and RELIABILITY, repairs, maintenance and adjustments (including brush inspection and replacement) should be performed by a DEWALT factory service center, a D EWALT authorized service center or other qualified service personnel. Always use identical replacement parts. Three Year Limited Warranty DEWALT will repair, without charge, any defects due to faulty materials or workmanship for three years from the date of purchase. This warranty does not cover part failure due to normal wear or tool abuse. For further detail of warranty coverage and warranty repair information, visit or call 1-800-4-D EWALT (1-800-433-9258). This warranty does not apply to accessories or damage caused where repairs have been made or attempted by others. This warranty gives you specific legal rights and you may have other rights which vary in certain states or provinces. In addition to the warranty, D EWALT tools are covered by our: 2 YEARS FREE SERVICE DEWALT will maintain the tool and replace worn parts caused by normal use, for free, any time during the first two years after purchase. 90 DAY MONEY BACK GUARANTEE If you are not completely satisfied with the performance of your DEWALT Power Tool, Laser, or Nailer for any reason, you can return it within 90 days from the date of purchase with a receipt for a full refund – no questions asked. RECONDITIONED PRODUCT: Reconditioned product is covered under the 1 Year Free Service Warranty. The 90 Day Money Back Guarantee and the Three Year Limited Warranty do not apply to reconditioned product. FREE WARNING LABEL REPLACEMENT: If your warning labels become illegible or are missing, call 1-800-4-DEWALT for a free replacement. POUR TOUT RENSEIGNEMENT SUPPLEMENTAIRE SUR CET OUTIL OU TOUT AUTRE OUTIL D EWALT, COMPOSER SANS FRAIS LE NUMERO : 1-800-4-DEWALT (1-800-433-9258) Regles de securite – Generalites AVERTISSEMENT ! Afin de reduire le risque de blessures, l'utilisateur doit lire le mode d'emploi. Tout manquement aux directives suivantes pose des risques de choc electrique, d'incendie et/ou de blessure grave. Le terme « outil electrique » dans tous les avertissements ci-apres se rapporte a votre outil electrique a alimentation sur sect...

Scarica la tua

Per scaricare, digitare 2 cifre :