valutazioni - 3, GPA: 4.7
(
)
)
|
Facilità d'uso
6 CARTON CONTENTS 1 2 Fig. 1 1. Motor and blower assembly 2. Stand 3 4 5 6 7 8 9 Fig. 1A 3. Dust intake port 4. Cloth-covered bag retainer ring (2) 5. One micron upper filter bag (2) 6. Six mil plastic lower bag (4) 7. Legs (2) 8. Bag retainer clamp (2) 9. Bag hanging rod (2) 7 1011 12 13 14 15 1617 1011 12 13 14 15 1617 Fig. 1B 10. Caster (4) 11. Intake cap and ring (3) 12. Bracket for bag hanging rod (2) 13. Knob for attaching legs to blower/motor assembly (4) 14. 3/8” (9.5mm) Lockwasher for attaching casters to stand (4) 15. 5/16” (8mm) Flat washers for attaching legs to blower/motor assembly and for the brackets (6) 16. M4 sheet metal screw for dust intake port (4) 17. 5/16” (8mm) Hex head screw for attaching bracket for bag hanging rod (2) UNPACKING AND CLEANING Carefully unpack the machine and all loose items from the shipping container(s). 8 ASSEMBLY ASSEMBLY TOOLS REQUIRED * Phillips head screwdriver * 12 mm wrench ASSEMBLY TIME ESTIMATE - 30 minutes to 1 hour FOR YOUR OWN SAFETY, DO NOT CONNECT THE MACHINE TO THE POWER SOURCE UNTIL THE MACHINE IS COMPLETELY ASSEMBLED AND YOU READ AND UNDERSTAND THE ENTIRE INSTRUCTION MANUAL. THIS MACHINE IS HEAVY. USE TWO OR MORE PEOPLE WHEN LIFTING. CASTERS 1. Turn stand (A) upside down, as shown in Fig 1C. 2. Place 3/8” lockwasher on caster stud (B) and screw caster into threaded hole on the bottom of the stand. Repeat for other three casters. 3. Tighten caster by hand, then set with a thin 14mm wrench. A B Fig. 1C LEGS TO MOTOR/BLOWER ASSEMBLY 1. Place motor/blower assembly with the motor (A) Fig. 2 down. 2. Place 5/16” flatwasher on knob (B). 3. Align holes on legs (C) with holes (D) in the motor/blower assembly. Legs should extend up. Insert knob through hole in the legs (C) and into threaded hole in the motor/blower assembly (D). Tighten knob securely. 4. Repeat steps for all knobs on both legs. Fig. 2 A D CB ATTACHING STAND TO LEGS ON MOTOR/BLOWER ASSEMBLY NOTE: TWO PEOPLE ARE NEEDED FOR THIS STEP. Place all four stand posts (A) Fig. 3 into four legs (B) on motor/blower assembly. Make sure metal base plates (D) are arranged over the large dust collection holes (C). Fig. 3 A B D C 9 B C ALTERNATE SETUP The steps so far will assemble the unit with the motor on top and dust intake ports on bottom, as shown in Fig 4. This unit can be assembled with the intake port (B) Fig. 5 in the up position by following the steps in “LEGS TO MOTOR/BLOWER ASSEMBLY.” The exception is to place the motor/blower assembly on a flat surface with the motor (A) Fig. 6 facing up before attaching legs. NOTE: BEFORE DOING THE ALTERNATE SETUP, REMOVE 5/16” HEX HEAD SCREWS FROM HOLES (B) FIG. 6 IN MOTOR/BLOWER ASSEMBLY AND PLACE IN HOLES (C). AIR LEAKAGE WOULD OCCUR IF SCREWS ARE NOT PLACED IN HOLES (C). A B C Fig. 6 DISCONNECT MACHINE FROM POWER SOURCE B C ALTERNATE SETUP The steps so far will assemble the unit with the motor on top and dust intake ports on bottom, as shown in Fig 4. This unit can be assembled with the intake port (B) Fig. 5 in the up position by following the steps in “LEGS TO MOTOR/BLOWER ASSEMBLY.” The exception is to place the motor/blower assembly on a flat surface with the motor (A) Fig. 6 facing up before attaching legs. NOTE: BEFORE DOING THE ALTERNATE SETUP, REMOVE 5/16” HEX HEAD SCREWS FROM HOLES (B) FIG. 6 IN MOTOR/BLOWER ASSEMBLY AND PLACE IN HOLES (C). AIR LEAKAGE WOULD OCCUR IF SCREWS ARE NOT PLACED IN HOLES (C). A B C Fig. 6 DISCONNECT MACHINE FROM POWER SOURCE Fig. 7 10 ATTACHING DUST COLLECTION BA DISCONNECT MACHINE FROM POWER SOURCE USING CLOTH COVERED FLEXIBLE RING: 1. Take cloth-covered bag retainer ring (A) Fig. 8 and place it inside opening of clear plastic dust collection bag. Fold about 6 inches of the bag down around the retainer ring. 2. Place bag in large hole (B) Fig. 8 in motor/blower assembly and fit retainer ring (A) Fig. 8 and (A) Fig. 9 into bottom groove (B) Fig. 9. It will be necessary to bend and fold the ring to fit it into place. 3. Tug slightly on bag to eliminate any slack and to make sure there is a good fit so the bag will not detach during collection. USING METAL BAG CLAMP: The plastic bag can also be attached to the outside of the dust collector using the included clamp (B) Fig. 10: 1. Place clamp (B) around top of plastic bag (A) and fold about 4 to 6 inches of plastic bag over the clamp as show in Fig. 10. 2. Place the clamp and plastic bag assembly (A) Fig. 10A and fasten clamp securely as shown. A B B A Fig. 10 B A Fig. 10A 11 ATTACHING TOP FILTER BAG DISCONNECT MACHINE FROM POWER SOURCE 1. Assemble 5/16” flatwasher (23 mm diam.) onto 5/16” hex head screw. 2. Position bracket (A) to dust collector as shown in Fig. 11. 3. Insert 5/16” hex head screw through hole in bracket and thread into the hole in dust collector. Tighten securely with a 12 mm wrench. 4. Insert rod (A) Fig. 12 into pocket on filter bag. 5. Insert rod (A) into hole in bracket (B). 6. Work open end of filter bag into top groove of dust collector drum until se...