valutazioni - 5, GPA: 4.4
(
)
)
|
Facilità d'uso
J Protect the charger, battery pack and the drill/ grinder from moisture. J Warning! Do not use the drill/grinder with chargers or batteries other than the charger/ battery pack supplied. J Warning! Never short circuit the battery pack. Overheating, fire or destruction of the battery pack may result. Therefore: -Do not connect any wires to the battery pack poles. -Take care that no metal objects (nails, screws, etc.) can short circuit the battery pack connectors. J m Attention! Never throw the battery pack into fire or water. Danger of explosion! Handle the battery pack with care, protect it from impacts and sharp blows! Attention! To avoid the danger of injury, burning and damage to health: J Warning! If you come into contact with the acid from the battery pack, wash off the acid thoroughly with water immediately. If acid should enter your eyes, flush them immediately with water and find a doctor immediately. J Caution! The tool continues to rotate after it has been switched off! Avoid contact with rapidly rotating drill / grinder components. J When you use the drill/grinder wear the following protective equipment: safety glasses and protective gloves. To work safely: J Before cleaning or maintaining the charger or battery pack always pull the plug out of the mains socket. J Never charge the battery pack if the ambient temperature is below 10°C or above 40°C. m Attention! To avoid damaging the tool or workpiece. J Do not allow the tool to come to a standstill by overloading it! Q Operation Q Charging the battery pack m Attention! A battery pack that has been unused for a while or never been charged must be charged before reuse or first use. The battery pack requires about 3-5 cycles before it can reach its full charge. m Attention! Always pull out the mains plug (mains adapter 9 ) before you insert the battery pack into or take it out of the charger. j Connect the adapter 93 to a mains socket. j Insert the battery pack into the charging cradle 8 . Make sure that the polarity of the battery pack matches that of charging cradle 8 . j The LED 10 lights up green whenever the battery pack 3 is in the charging cradle 8 and the adapter 9 is connected to a mains socket. J Do not use the quick-charge process to charge a battery pack for a second time in close succession. Otherwise there is the danger that the battery pack will become overcharged and its useful life and that of the charger reduced. GB/IE/CY J Switch the charger off for at least 15 minutes between successive charging processes. To do this pull the mains plug (mains adapter 9 ) out of the socket. Q Inserting / removing the battery pack into/out of the drill/grinder Inserting the battery pack: j Set the On/Off switch 31 to position “0”. j Insert the battery pack into the drill/grinder until it engages. Removing the battery pack: j Pressing the battery pack buttons 2 at the sides at the same time allows you to remove the battery pack 3 . Q Changing a collet j Press the spindle lock 75 and keep it pressed. j Rotate the clamping nut until the lock engages. j Release the clamping nut 55 .7 . from the thread and remove the collet 18. j Insert the correct collet 18 and screw it tight with the clamping nut j Release the spindle lock Q Inserting/changing tools j Press the spindle lock 75 and keep it pressed. j Rotate the clamping nut until the lock engages. j Release the clamping nut 5 using the open spanner end of the combination tool 23. j If a tool is already inserted remove it. j First insert the tool you wish to use though the clamping nut 5 before you insert it into the Operation using the open spanner end of the combination tool 23. Note: Use the screwdriver end of the combination tool 23 to release or tighten the screw of the mandrels 12. Q Switching on and off/Setting the speed range Switching on/Setting the speed range: j Set the On/Off switch 1 to a position between “2” and “10”. Switching off: j Set the On/Off switch 1 to position “0”. Q Advice on working with materials/Tools/Speed ranges j Make sure that no debris from working the material adheres to the tool. Use paraffin, cutting oil or similar medium to lubricate the tool. j Use the highest speed when working on steel or iron with the milling bits. j Use a short trial on a test piece to determine the optimum rotational speed range for working on zinc, zinc alloy, aluminium, copper and lead. j Use the low speed range for working on plas tics and low-melting point materials. j Use high speeds on wood. j Use the medium speed range for cleaning, polishing and buffing. The following information shall be considered as recommendatory only. Learn by practical experience which tools and settings are the best for the materials you work with. collet 18. j Press the spindle lock 7 and keep it pressed. j Insert the collet 18 into the threaded insert and screw the clamping nut 5 tightly on the thread GB/IE/CY Operation Setting the appropriate speed Symbols on On / off switch 1 Material 0 (Drill / grinder swi...
Questo manuale è adatto anche per i modelli :Altri strumenti - 6 V (511.05 kb)