|
Facilità d'uso
1 K J O H C N FIG. 2 P L M FIG. 3 C I D25602 W CTC COMPLETE TORQUE CONTROL DEWALT INDUSTRIAL TOOL CO., BALTIMORE, MD 21286 USA FOR SERVICE INFORMATION, CALL 1-800-4-DEWALT SER. D25XXX 1 3/4" (44mm) SDS MAX ROTARY HAMMER AFIN DE MINIMISER LES RISQUES DE BLESSURES, L’UTILISATEUR DOIT LIRE LE GUIDE D’UTILISATION.TOUJOURS UTILISER UNE PROTECTION OCULAIRE, AUDITIVE ET RESPIRATOIRE ADEQUATE. UTILISER LA POIGNEE LATERALE. LEA EL MANUAL DE INSTRUCCIONES PARA UN FUNCIONAMIENTO SEGURO. SIEMPRE UTILICE PROTECCION ADECUADA PARA LOS OJOS, OIDOS Y VIAS RESPIRATORIAS. SIEMPRE UTILICE EL MANGO LATERAL. TO REDUCE THE RISK OF INJURY, USER MUST READ INSTRUCTION MANUAL. ALWAYS USE PROPER EYE, EAR AND RESPIRATORY PROTECTION. ALWAYS USE SIDE HANDLE. Service Lock-On Brush Service WARNING AVERTISSEMENT ADVERTENCIA FIG. 5 G V S T U FIG. 4 M P R Q J SOFT START FEATURE The soft start feature allows you to build up speed slowly, thus preventing the drill bit from walking off the intended hole position when starting. The soft start feature also reduces the immediate torque reaction transmitted to the gearing and the operator if the hammer is started with the drill bit in an existing hole. Hammerdrilling with a Solid Bit D25501, D25553, D25602, D25651 NOTE: The D25831, D25851 have only chipping modes with no hammerdrilling capability. 1. Set the mode selector (F) to hammerdrilling mode. 2. For D25602 and D25651 only, move the torque control lever (U) to Setting 1 (S). 3. Set the speed and impact control dial (G). 4. Insert the appropriate drill bit. 5. Adjust the side handle (front or rear position) (C). 6. Mark the spot where the hole is to be drilled. 7. Place the drill bit on that mark and depress the trigger switch (A). 8. Apply only enough pressure to engage active vibration control (refer to Active Vibration Control). 9. To stop the tool, release the trigger switch. Always turn the tool off when work is finished and before unplugging. Hammerdrilling with a Core Bit D25501, D25553, D25602, D25651 CAUTION: Do not use a core bit for hammerdrilling wood. Personal injury and damage to tool may result. NOTE: The D25831, D25851 have only chipping modes with no hammerdrilling capability. 1. Set the mode selector (F) to hammerdrilling mode. 2. For D25602 and D25651 only, move the torque control lever (U) to Setting 2 (T). 3. Turn the speed and impact control dial (G) to the maximum speed (level 7). 4. Adjust the side handle (front or rear position) (C). 5. Assemble the centering bit and adapter shank into core bit. 6. Mark the spot where the hole is to be drilled. 7. Place the centering bit on that mark and depress the trigger switch (A). NOTE: Some core drills require the removal of centering bit after about 1 cm of penetration. If so, remove and continue hammerdrilling. 8. When hammerdrilling through a structure thicker than the depth of the core bit, break away the round cylinder of concrete or core inside the bit at regular intervals. To avoid unwanted breaking away of concrete around the hole, first drill a hole the diameter of the centering bit completely through the structure. Then drill the cored hole halfway from each side of the structure. 9. To stop the tool, release the trigger switch. Always turn the tool off when work is finished and before unplugging. Chipping D25831, D25851 1. Set the mode selector (F) to chipping mode. 2. Set the impact control dial (G) to desired setting (refer to Electronic Speed and Impact Control). 3. Insert the appropriate chisel and rotate it by hand to lock it into the desired position. NOTE: For SDS Max® models, only use SDS Max® bits. 4. Adjust the side handle (front or rear position) (C). 5. Depress the trigger switch (A). 6. Apply only enough pressure to engage active vibration control (refer to Active Vibration Control). 7. To stop the tool, release the trigger switch. Always turn the tool off when work is finished and before unplugging. MAINTENANCE WARNING: To reduce the risk of serious personal injury, turn tool off and disconnect tool from power source before making any adjustments or removing/installing attachments or accessories. Cleaning WARNING: Blow dirt and dust out of all air vents with dry air at least once a week. Wear proper ANSI Z87.1 (CAN/CSA Z94.3) eye protection and proper NIOSH/OSHA/MSHA respiratory protection when performing this. WARNING: Never use solvents or other harsh chemicals for cleaning the non-metallic parts of the tool. These chemicals may weaken the plastic materials used in these parts. Use a cloth dampened only with water and mild soap. Never let any liquid get inside the tool; never immerse any part of the tool into a liquid. Lubrication Your tool was properly lubricated before leaving the factory. In from two to six months, depending upon use, take or send your tool to an authorized service center for a complete cleaning, inspection and lubrication. Tools used constantly on production jobs will need relubrication more often. Also, tools “out of ...
Questo manuale è adatto anche per i modelli :Altri strumenti - D25851 (902.76 kb)
Altri strumenti - D25602 (902.76 kb)
Altri strumenti - SDS Max D25651 (902.76 kb)
Altri strumenti - SDS Max D25553 (902.76 kb)