valutazioni - 4, GPA: 4
(
)
)
|
Facilità d'uso
Use the correct tool for your application. The correct tool will do the job better and safer at the rate for which it is designed. 14) Do not use tool if switch does not turn it on or off. A tool that cannot be controlled with the switch is dangerous and must be repaired. 15) Disconnect battery pack from tool or place the switch In the locked or off position before making any adjustments, changing accessories, or storing the tool. Such preventive safety measures reduce the risk of starting the tool accidentally. 16) Store idle tools out of reach of children and other untrained persons . Tools are dangerous in the hands of untrained users. 17) When battery pack is not In use, keep It away from other metal objects like: paper clips, coins, keys, nails, screws, or other small metal objscts that can make a connection from one terminal to another. Shorting the battery terminals together may cause sparks, bums or a fire. 16) Maintain tools with care. Keep cutting tools sharp and clean. Properly maintained tools with sharp cutting edge are less likely to bind and are easier to control. 19) Check for misalignment or binding of moving parts, breakage of parts, and any other condition that may affect the tool's operations. H damaged, have the tool serviced before using. Many accidents are caused by poorly maintained tools. 20) Use only accessories that are recommended by the manufacturer for your model. Accessories that may be suitable for one tool may create a risk of injury when used on another tool. Service 21) Tool service must be performed only by qualified repair personnel. Service or maintenance performed by ~ unqualified personnel may result in a risk of injury. 22) When servicing a tool, use only identical replacement parts. Follow instructions In the Maintenance section of this manual. Use of unauthorized parts or failure to follow Maintenance Instructions may create a risk of shock or injury. SPECIFIC SAFETY RULES 1) Hold tool by Insulated gripping surfaces when performing an operation where the cutting tool may contact hidden wiring. Contact with a “live" wire will make exposed metal parts of the tool live” and shock the operator. 2) Wear ear protectors when using the tool for extended periods. Prolonged exposure to high intensity noise can cause hearing loss. 3) Be aware that this tool Is always In an operating condition, it does not have to be plugged into an electrical outlet. 4) Do not operate the reversing lever when the main switch is on. The battery will discharge rapidly and damage to the unit may occur. 5) If the bit becomes Jammed, Immediately turn the main switch off to prevent an overload which can damage the battery pack or motor. Use reverse motion to loosen jammed bits. 6) When storing or carrying the tool, set the reversing lever to the center (switch lock) position. 7) Do not strain the tool by holding the speed control trigger halfway (speed control mode) so that the motor stops. 8) During charging, the charger may become slightly warm. This Is normal. Do not charge the battery for a long period. FOR BATTERY CHARGER & BATTERY PACK <> SAVE THESE INSTRUCTIONS ». manual contains important safety and operating instructions for battery charger EY0214. 2) Before using battery charger, read all instructions and cautionary markings on (1) battery charger, (2) battery pack. 3) CAUTION -To reduce the risk of Injury, charge only Battery Pack as shown below. EY9103, EY9101, EY9001, EY9006, EY9180, EY9080, EY9182, EY9086, EY9065, EY9106, EY9107, EY9136, EY9117, EY9230, EY9200, EY9108, EY9210 Other types of batteries may burst causing personal injury and damage. 4) Do not expose charger to rain or snow. 5) To reduce risk of damaging the electric plug and cord, pull by plug rather than cord when disconnecting charger. 6) Make sure cord is located so that it will not be stepped on, tripped over, or otherwise subjected to damage or 8trB88. Symbol meaning V Volts --- Direct Current n* no load speed .Jmin revolutions or reciprocation per minutes o Forward Rotation o Reverse Rotation T Rotation with Hammering «a Rotation only 7) An extension cord should not be used unless absolutely necessary. Use of Improper extension cord could result in a risk of fire and electric shock. If extension cord must be used, make sure: a. that pins on plug of extension cord are the same number, size and shape as those of plug on charger. b. that extension cord is properly wired and in good electrical condition. c. that wire size is large enough for ampere rating of charger as specified below. RECOMMENDED MINIMUM AWG SIZE OF EXTENSION CORDS FOR BATTERY CHARGERS AC Input Rating. Ampere AWQ Size of Cord Equal to or But lata greater lhan than Length of Cord, Feat 25 50 100 160 0 2 18 18 18 16 8) Do not operate charger with damaged cord or plug—replace them immediately. 9) Do not operate charger if it has received a sharp blow, been dropped, or otherwise damaged in any w...