valutazioni - 2, GPA: 5
(
)
)
|
Facilità d'uso
Use of any other parts will void the warranty. Only use parts and accessories intended for use with this tool, which are available from Harbor Freight Tools. SPECIAL WARNINGS WHEN USING THIS LOG SPLITTER Using this poweful tool may create special hazards. Take particular care to safeguard yourself and those around you. Hydraulic systems. Never operate this tool if there is a hazard presented by hydraulic fluid. Before using the splitter, check for hydraulic leaks. Be sure the tool and your work area are clean and free of oil spills. Hydraulic fluid can create hazards, causing you to slip and fall, your hands to slip while using the machine, or fire hazard. Electrical Safety. Never operate this tool if there is an electrical hazard. Never operate an electrical tool in wet conditions. Never operate this tool with an improper electrical cord or extension cord. Never operate this tool unless you are plugged into a properly grounded outlet, which supplies 110120Volts, and is protected by a 30 Amp circuit breaker. Physical Hazards. Log Splitting creates special physical hazards. Never operate this tool unless you are wearing proper safety gloves, hard-toed shoes and ANSI-approved eye protection. Be careful of the splinters that will be produced, to avoid puncture injury and potential jamming of the tool. Never try to split logs which are too large or small to fit properly within the tool. Never attempt to split logs containing nails, wire or other debris. Clean up as you work; accumulated split wood and wood chips can create a hazardous work environment. Never continue to work in a cluttered work area which may cause you to slip, trip or fall. Keep onlookers away from this tool, and never allow unauthorized persons to operate this tool. NOTICE: No list of warnings can be all inclusive. The operator must supply common sense, and operate this tool in a safe manner. Page 4 SKU # 40318 ASSEMBLY The only assembly required is as follows: Screw Handle A (D Below) into Handle B (E Below). The Log Splitter is ready for use, after reading and adhering to all Saftety Warnings and Cautions, and Operation and Maintenance instructions provided in this manual. Figure 2 Major Components Overview A Wedge B Log Guiding Plates C Log Pusher/Lifting Handle D Handle A E Handle B F Shield G Pump Cover H Main Body I Motor Base J Motor Assembly K Motor Start Switch L Wheels Page 5 SKU # 40318 OPERATION OPERATION 1. Plan your work site. Work safely and save effort by planning your work before hand. Have your logs positioned where they can be easily reached. Have a site located to stack the split wood or load it onto a nearby truck or other carrier. 2. Prepare the logs for splitting. This splitter accomodates logs up to 14-1/2” in length. When cutting up limbs and large sections, do not cut sections any longer than 14”. Do not attempt to split green logs. Dry, seasoned logs split much more easily, and will not jam as frequently as green wood. 3. Route the power cord. Locate an appropriate power outlet, and secure an adequate extension cord, if needed. Route the cord from the splitter to the power source in a way that safeguards against tripping on the cord, or the cord becoming damaged during the work session. Be sure to avoid wet conditions. 4. Position Splitter Securely. Be sure the Splitter is positioned firmly on level, solid ground. If necessary, block the Wheels (#25) with wedges to prevent them from rolling. 5. Open the Air Bleed. Loosen the Bleed Screw (#14) - [located on the Front Cover (#15)] 3-4 turns whenever the splitter is being used. Retighten this screw when you are finished. 6. Place log onto Splitter. Place the log onto the splitter, lengthwise and lying flat on the Main Body (#47). The log should lie flat on the Splitter, and be cradled by the Guide (#46). Never attempt to split a log at an angle. Be sure the Wedge and Log Pusher (#49) will contact the log squarely on the ends. 7. Two hand operation. When it is safe to do so, depress the Switch (#36) with one hand. Wait a few seconds as the motor spins up and creates pressure in the Hydraulic pump. Then, when it is safe to do so, depress the Handle A (#60). The Log Pusher (#49) will compress the log, pushing it against the Wedge, splitting the log. Once the log is split, release both the Switch (#36) and Handle A (#60); this will allow the Log Pusher (#49) to retract. Warning: If the log does not split immediately, do not force it by maintaining the thrust for more than a few seconds. This can damage the tool. It is better to try repositioning the log on the splitter, or setting the log aside. 8. Stack as you work. This will provide a safer work area, by keeping it uncluttered, and avoid the danger of tripping, or damaging the power cord. 9. Remember to retighten the Bleed Screw (#14) when you are finished. Page 6 SKU # 40318 GROUNDING / VOLTAGE WARNING Common household current is 110-120 volts. As long as the outlet used with this tool is rated from 110-120V there will ...