valutazioni - 3, GPA: 4
(
)
)
|
Facilità d'uso
for support. Troubleshooting Table WHEN PERFORMING ANY MAINTENANCE, YOU MUST FIRST UNPLUG THE WOOD SPLITTER FROM THE POWER SOURCE AND MAKE SURE THE HYDRAULIC SYSTEM IS DEPRESSURIZED AND THE FLUID HAS COOLED. READ THE "GENERAL SAFETY RULES" (CHAPTER 2) OF THIS MANUAL BEFORE PERFORMING ANY REPAIRS OR MAINTENANCE. SYMPTOM POSSIBLE CAUSE Ram will not move or is slow to . Is the Bleed Screw adjusted properly? See page 13, Step 3. respond. . Bleed any accumulated air from the hydraulic system. See page 20, step 5. . Is the wood splitter on a level surface? See page 13, step 1. . Make sure the voltage at the outlet or extension cord connection to the wood splitter is at least 105VAC. . The hydraulic fluid may be low. Check and adjust the level as required; see page 20. . The wood being split may be too hard, it has knots or its fiber is very tough. Log fails to split. . Check the possible causes for the previous Ram operation symptom. . Incorrect positioning of the log. Re-position the log flat on the splitting beam with the ends squarely against the Ram face and Splitting Wedge. . Log exceeds permitted dimensions or the wood is too hard for the capacity of the machine. The maximum log length is 20" with a maximum diameter of 16" for the DR 6 -TON ELECTRIC WOOD SPLITTER. . The wedge has burrs or nicks and needs to be sharpened; see page 20. . There may be a hydraulic fluid leak. Locate the leak using a piece of cardboard under the machine and call 1(800) DR-OWNER (376-9637), or a qualified hydraulic mechanic for assistance, to replace worn components. . Hydraulic pressure is too low. Call 1(800) DR-OWNER (376-9637), or a qualified hydraulic mechanic for assistance to replace worn components. CALL TOLL FREE 1-800-DR-OWNER WHEN PERFORMING ANY MAINTENANCE, YOU MUST FIRST UNPLUG THE WOOD SPLITTER FROM THE POWER SOURCE AND MAKE SURE THE HYDRAULIC SYSTEM IS DEPRESSURIZED AND THE FLUID HAS COOLED. READ THE "GENERAL SAFETY RULES" (CHAPTER 2) OF THIS MANUAL BEFORE PERFORMING ANY REPAIRS OR MAINTENANCE. SYMPTOM POSSIBLE CAUSE Ram advances with a jerky motion or with strong vibrations. . Check the possible causes for the Ram operation symptom on the previous page. . Check the hydraulic fluid level; see page 20. . Bleed any accumulated air from the hydraulic system. See page 20, Step 5. If the problem persists, call 1(800) DR-OWNER (376-9637) for assistance. Hydraulic fluid leaking from the Ram or other external parts. . Check that the Bleed Screw has been tightened before moving the machine. Use care: Do not over tighten and strip the Bleed Screw Threads. . The hydraulic fluid seals may be worn. Call 1(800) DR-OWNER (376-9637), or a qualified hydraulic mechanic for assistance to replace worn components. NOTE: Country Home Products, Inc. has provided Parts Lists and Schematic Diagrams as reference tools only. CHP makes no representation or warranty of any kind to the buyer that he/she is qualified to make any repairs to the product or that he/she is qualified to replace any parts of the product. In fact, CHP expressly states that all repairs and parts replacement should be undertaken by certified and licensed technicians and not by the buyer. The buyer assumes all risk and liability arising out of his/her repairs to the original product or replacement parts thereto, or arising out of his/her installation of replacement parts thereto. DR® WDS 6.3, 6 -TON ELECTRIC WOOD SPLITTER CHAPTER 7 PARTS LISTS, SCHEMATIC DIAGRAMS AND WARRANTY Parts List - DR 6 -TON ELECTRIC WOOD SPLITTER NOTE: Part numbers listed are available through Country Home Products, Inc. Ref# Part# Description Ref# Part# Description 01 205271 Nut, Hex, M16 35 205901 Plate, Log Guiding, Left 02 205281 Nut, Hex, M16 (Thin) 36 205911 Bolt, M8 x 10 03 205291 Piston Ram 37 202481 Bolt, M8 x 14 04 205301 Spring 38 205921 Plate, Sleeve, Plastic 05 205311 O-ring, Oil Seal 39 205931 Log Pusher Assembly 06 205321 Piston 40 182111 Cover, Oil Cylinder, Front 07 205331 O-ring, Oil Seal 41 205941 Cover Seal, Paper, Square 08 205341 Square Piston Ring 42 205041 Spring 09 205351 Cylinder 43 205121 Screw, Fixing, M8 x 10 10 182181 Dip Stick 44 202751 Base, Handle 11 182191 O-ring, Oil Seal 45 205031 Bar, Handle, Short 12 202161 Seal, Ring, Teflon, Anti-Dust 46 206121 Bar, Grip Handle, Long 13 202171 O-ring, Oil Seal 47 204421 Washer, Flat, M4 14 211611 Bleed Screw, w/Washer, M4 x 10 48 206031 Washer, Copper, M12 15 204371 Cover, Oil Cylinder, End 49 206041 Nut, M12 16 205411 Bolt, Two Head 50 206151 Plate, Support 17 205421 Bolt, Two Head, Long 51 206161 Washer, Flat, M12 18 203721 Foot, Rubber, Motor, Left 52 206171 Nut, M12 19 204651 Foot, Rubber, Motor, Right 53 206181 Bolt, M8 x 20 20 202701 Motor and Pump Assembly 54 206071 Circlip, Axle 21 204681 Nut, M8 55 206081 Wheel, Rubber 22 204691 Screw, M8 56 192011 Frame, Stand, Wheel 23 204801 O-ring, Oil Seal 63 205951 Circlip, Spindle 24 202491 Washer, Flat, M8 64 205961 Sleeve 25 204771 Washer, Spring, M8 65 205971 Spring 26 204...