valutazioni - 3, GPA: 4
(
)
)
|
Facilità d'uso
The use of an extension cable suitable for outdoor use reduces the risk of electric shock. 3. Personal safety a) Remain alert at all times, watch what you are doing and always proceed with caution. Do not use the device if you are tired or under the influence of drugs, alcohol or medication. One moment of carelessness when using the device can lead to serious injury. GB/IE Safety notes / Operation b) To avoid the danger of injury, burning and damage to health: DANGER OF BURNS! The glue and the nozzle can reach temperatures of 200 °C. Do not touch the nozzle or the glue. Keep other people and animals away from the hot glue. On contact with the skin, hold the affected part under running cold water for several minutes. Do not try to remove the glue from the skin. 4. Careful handling and use of electrical power tools a) Pull the mains plug from the socket before you make any adjustments to the device, change accessories or when the device is put away. This precaution is intended to prevent you from unintentionally starting the device. b) When not in use always ensure that electrical power tools are kept out of reach of children. Do not let anyone use the device if he or she is not familiar with it or has not read the instructions and advice. Electrical power tools are dangerous when they are used by inexperienced people. Let the device cool down completely before putting it away. The hot nozzle can cause damage. c) Look after the device carefully. Check that moving parts are working properly and move freely. Check for any parts that are broken or damaged enough to detrimentally affect the functioning of the device. Have damaged parts repaired before you use the device. Many accidents have their origins in poorly maintained electrical power tools. d) Always work with the mains lead leading away from the rear of the device. Operation Before first use Preparing the glue site: . Do not use inflammable solvents to clean the glue site. . The ambient temperature and temperature of the materials to be glued must be not less than + 5° C and not warmer than + 50° C. . The glue sites must be clean, dry and free of grease. . Smooth surfaces should be roughened before gluing. . Warm any materials that are prone to cool down quickly (e.g. steel) to improve the bond with the glue. Screw on the appropriate nozzle and fit the wire stand 6 . 8 Preparing the tool for use Working with the mains lead connected: 1. Connect the mains lead 11 to the glue gun connection 10 (see Fig. F). Insert the mains plug into the mains socket. 2. Fold forward the wire stand Stand the device up. 6 . 3. Push a glue stick into the feed channel 1 . 4. Let the device heat up for about 4 minutes. The device is now ready for use. Cordless working: 1. Connect the mains lead 3 . 11 to the charger connection Insert the mains plug into the mains socket. 2. Place the glue gun into the charger 4 . 3. Push a glue stick into the feed channel 1 . 4. Let the device heat up for about 4 minutes. The device is now ready for use. 5. Repeat the heating-up procedure if the feed switch becomes stiff or the outcoming glue becomes viscous. GB/IE Operation / Maintenance and Cleaning / Service / Warranty Gluing: . Press the feed clamp 5 to regulate the flow of glue as required for your work. 1. Apply the glue in individual dots. Apply in zigzags on flexible materials such as fabrics. 2. Immediately after applying the glue, press the two materials together for about 30 seconds. The glued joint can be loaded after about 5 minutes. 3. When you take a break from work, set the glue gun down on the wire stand 6 or in the charger 4 . 4. Remove any glue residue with a sharp knife after cooling. Glued joints can be loosened again by applying heat. Switching off the device: . Pull the mains lead out of the mains socket. Changing the nozzle: Wear protective gloves. . Heat up the device for about 4 minutes. Change the nozzle 8 when it is hot. DANGER OF BURNS! Touch the nozzle 8 only by the heat shield 9 . The nozzle tip is hot! Maintenance and Cleaning The glue gun is maintenance-free. . WARNING! Pull the mains lead out of the mains socket before you clean the tool. . Always keep the device clean and dry. . Do not allow any liquids to enter the tool. Use a soft cloth to clean the housing. Never use petrol, solvents or cleaning agents that might attack plastic. Service repaired only by qualified specialist personnel using original manufacturer WARNING! Have your device parts only. This will ensure that your device remains safe to use. WARNING! If the plug or mains lead needs to be replaced, always have the replacement carried out by the manufacturer or its service centre. This will ensure that your device remains safe to use. Warranty The warranty for this appliance is for 3 years from the date of purchase. The appliance has been manufactured with care and meticulously examined before delivery. Please retain your receipt as proof of purchase. In the event of a warranty claim, pleas...