valutazioni - 1, GPA: 5
(
)
)
|
Facilità d'uso
All rights reserved. Assembling the Roller Checking the Inlet Valve If the unit is new or has been stored for an extended period of time Installing the Batteries and Attaching the Strap the inlet ball can become stuck and the pump may be difficult to prime. To check: 1. Open the battery door. The battery door is located on the drive housing. 2. Insert the batteries in the proper direction. +- +--+ -+ CAUTION Improper installation of batteries may cause batteries to overheat and leak acid. Acid may cause severe injury and/or property damage. NOTE: Use high quality alkaline batteries only. 3. Attach the strap to the loops on the drive housing. Removing and Attaching the Drive Housing to the Fluid Tank Close Open 1. Remove the drive housing by turning the drive housing counterclockwise. 2. Attach the drive housing by setting it onto the fluid tank at a 90° angle and turning clockwise. Attaching the Fluid Hose 1. Slide the fluid hose through the anti-kinking spring and the spring clip. 2. Push the fluid hose to the port on the side of the drive housing. 3. Slide the spring clip over the fitting to keep the hose securely in place. 4. Slide the anti-kinking spring up against spring clip. Fluid Hose Inlet Ball 1. Turn the valve body Retainer counterclockwise and pull Ball down to remove. Inlet Ball 2. Shake the inlet valve Inlet Valve Holder assembly gently. If it does Assembly not rattle, remove the inlet ball retainer and clean the ball. 3. Reassemble the inlet valve. Filling the Fluid tank 1. Place the drive housing on the fluid tank at a 90° angle. 2. Remove the fluid tank cap and fill the tank with paint. 3. Wipe the lip, threads, and body of the fluid tank to remove any spilled or splattered material. 4. Replace the cap and lock the drive housing securely onto the fluid tank. Using the Roller The On/Off switch has two speeds for controlling the paint flow – High and Low. Choose the setting which is appropriate for your application. If too much paint is being delivered to the roller on High speed, use the Low speed setting. If paint flow is still too great, shut the roller off, then turn back on when more paint is needed. Applying Paint Begin rolling as paint appears to saturate the roller cover. If paint is flowing faster than you can roll,turn the pump off until more paint is needed. NOTE: Do not place the roller below the level of the paint when not in use. Paint will siphon to roller even if motor and pump are turned off. ©1997 Wagner Spray Tech. All rights reserved. 3 English R Cleanup A thorough cleaning after each use of the roller is important to keep it in good working order. Do not turn the roller upside down or on its side. If liquid gets inside the drive housing it could damage the unit. Quick Cleanup The following steps outline the basic cleanup procedures. For more detailed instructions on how to perform each step, refer to the Detailed Cleanup section in this manual. 1. Clean the roller cover. 2. Remove paint in hose. 3. Empty fluid tank. 4. Clean hose. 5. Clean roller handle. 6. Remove the pump assembly. 7. Remove and clean the valves. 8. Clean the pump assembly. 9. Clean and lubricate the 10. Reassemble the pump and piston and O-ring. attach it to the drive housing. Detailed Cleanup Cleaning the Roller Cover 1. Pull one end of the splatter shield out of the end cap and slip opposite end off of the roller handle. 2. Press the locking tab and remove the roller cover and roller core. 3. Unscrew the end cap and slide the roller cover off of the roller core. 4. Clean the roller cover with the appropriate solvent. Removing Paint from the Hose and Container 1. Remove the drive housing from fluid container. 2. Hold the roller handle over the paint pail and run the pump to remove excess paint from hose and pump. 3. Pour remaining paint from container back into paint pail. Cleaning the Hose Thoroughly For Latex: 1. Remove the hose from the motor compartment. 2. Insert the hard plastic tube of the faucet adapter into the paint hose. 3. Push the adaptor over a faucet. 4. Slowly increase the water pressure and run water through the hose and handle until the water come out clean. For Oil: 1. Fill the paint container with the appropriate solvent recommended by the paint manuafacturer. 2. Circulate the solvent through hose and roller arm for several minutes. Cleaning the Roller Handle Assembly 1. Remove the seal from the end of the roller handle. Note the direction of the lip for correct replacement. 2. Clean the handle and seal thoroughly. 3. Apply a thin layer of petroleum jelly to the seal. 4. Replace the seal in the proper direction. Removing the Pump from the Drive Housing 1. Turn the retaining nut on the pump counterclockwise. 2. Pull out the pump assembly. 3. Wipe excess paint off of the piston. 4. Apply a thin layer of petroleum jelly to the pump O-Ring. NOTE: The piston will remain attached. 1 2 3 NOTE: For latex, clean roller cover, core and end cap thoroughly in warm soapy water. For oil-based pai...