Make any needed repairs or replace the cord if necessary. Side Handle For operating convenience, the side handle can be rotated to any position around the tool (360s). NEVER OPERATE TOOL WITHOUT SIDE HANDLE IN PLACE. Depth Rod To adjust the depth rod, loosen the handle and move rod so that the distance between the end of the rod and the end of the bit equals the desired drilling depth (Figure 1). NOTE: Bit must be fully seated in the hammer when measuring. Figure 2 shows how the depth rod c

The smaller the gauge number of the wire, the greater the capacity of the cable, that is 16 gauge has more capacity than 18 gauge. When using more than one extension to make up the total length, be sure each individual extension contains at least the minimum wire size. To determine the minimum wire size required, refer to the following chart. CHART FOR MINIMUM WIRE SIZE (AWG) OF EXTENSION CORDS NAMEPLATE RATING-AMPS TOTAL EXTENSION CORD LENGTH - FEET 25 50 75 100 125 150 175 200 0-10.0 10.1

The variable speed switch allows slow starting when hammering for exact hole positioning or when working with brittle surfaces such as glazed tile. The further the trigger is depressed, the higher the R.P.M. (Revolutions Per Minute) and B.P.M. (Beats Per Minute). Releasing the trigger turns the tool off. Changing Bits Your tool is designed for the B&D SDS bit system in sizes from 3/16” to 3/4” diameter. To change a bit: 1. Unplug the unit from power source. 2. Insert the bit with a slight tw

Wipe plastic parts with a soft cloth lightly dampened with soapy water. 26. ALWAYS KEEP THE MOTOR AIR VENT FULLY CLEARED. A constantly open motor air vent is necessary to allow air to come in and out for cooling the motor. Do not allow it to become clogged. 27. OPERATE POWER TOOLS AT THE RATED VOLTAGE. Operate power tools at voltages specified on their nameplates. 28. NEVER TOUCH THE MOVING PARTS. Never touch the moving parts such as blades, bits or cutters. 29. STOP OPERATION IMMEDIATELY IF

When servicing Double Insulated Tools, USE ONLY IDENTICAL REPLACEMENT PARTS. 8 Precautions On Using Your Pavement Breaker 1. Always wear a face mask when operating this tool. 2. Use earplugs when operating for extended periods. 3. Be sure to lock the bit holder in position. 4. The bit becomes extremely hot during operation. Avoid touching it without heavy gloves. 5. Check all screws for tightness before operation. 6. When working at elevated locations, be alert to objects and persons bel

Secure safe operation through correct handling by observing the instructions described herein. Do not employ accessories other than those specified herein; otherwise, a hazardous condition may be created. Never allow a power tool to be used by persons not familiar with correct handling (such as children) or by those who cannot handle the tool correctly. 22. CONFIRM THAT NO ITEMS SUCH AS AN ELECTRIC CABLE OR CONDUIT ARE BURIED INSIDE. In places where live wiring may be hidden behind a wall, floo

Should you be determined to make a repair yourself, remember that the green colored wire is the “grounding” wire. Never connect this green wire to a “live” terminal. If you replace the plug on the power cord, be sure to connect the green wire only to the grounding (longest) prong on a 3-prong plug. EXTENSION CORD When using the tool at a considerable distance from power source, an extension cord of adequate size must be used to prevent loss of power and over-heating. Use the table below to det

Many household cleaners contain chemicals which could seriously damage the plastic. Also, do not use gasoline, turpentine, lacquer or paint thinner, dry cleaning fluids or similar products. Never let any liquid get inside the tool; never immerse any part of the tool into a liquid. Important To assure product SAFETY and RELIABILITY, repairs, maintenance and adjustments should be performed by Black & Decker Service Centers or other qualified organizations, always using Black & Decker replacement

Never connect this green wire to a “live” terminal. If you replace the plug on the power cord, be sure to connect the green wire only to the grounding (longest) prong on a 3-prong plug. MOTOR Your Black & Decker tool is powered by a B & D-built motor. Be sure your power supply agrees with voltage marked on nameplate. Volts 50/60 Hz means Alternating Current only. Volts DC-60 Hz or AC/DC means it will also operate on Alternating Current or Direct Current. Voltage variation of more than 10% will

Use witn and 1* Hammers. Can also tot used with IVfe" Hammer, (requires an extra Chuck Wrench No. 22749). Cat. Me. Point Diam. Over- all Lgth. CMy. In box Cat No. Point Diam. Over- all Lgth. ity. in box 7187 ' 5s........... 6 7182 %" 9" 6 7188 s/ir 5" 6 8372 W 18" 1 7180 %" 5" 6 7171 11/16" 9" 6 7188 7/16* 5« 6 7183 9" 6 7181 Угт 9" 6 8380 %" 18* 1 8384 mm 18" 1 8382 %" 24* 1 7170 9/16" 9" 6 90038 mm 9* 6 50082 i" 9« 6 24873 23081 23082 23083 1172 7097 •38« 8388 11/16" w %"