CHECK DAMAGED PARTS. Before using any tool, any part that appears damaged should be carefully checked to determine that it will operate properly and perform its intended function. Check for alignment and binding of moving parts; any broken parts or mounting fixtures; and any other condition that may affect proper operation. Any part that is damaged should be properly repaired or replaced by a qualified technician. 14. REPLACEMENT PARTS AND ACCESSORIES. When servicing, use only identical replacem

A B B DE 1, Turn base (A) right side up, Align the mounting hobs at the base of blower and motor assembly (B) with six pre-drilled hobs (C) in base and fasten with six 5/16=18 x 5/8" hex head screws (D) and 5/16" lock washer (E), See figure 8, Fig. 9 G 2, 3, 11 Assemble drum support (F) to the two threaded hobs in the corner of base with two 5/16=18 x 5/8" hex head screws and 5/16" lock washer (G), NOTE: Do not completely tighten hardware at this time, See figure 9, Assemble the remaining drum s

See Product Specifications on page 2 for your dust collector maximum static pressure. NOTE: To determine if you have met the Static Pressure Requirement when using a Dust Collection System, identify the branch of the system with the highest static pressure requirement first, If you run your Dust Collection System with more than one blast gate open, add the static pressure from all branches that are open to determine the total static pressure requirements, Static Pressure Requirement Chart Size o

(no _oad R.P.M.) ST COLL Mode_ No. 152.213361 C CAUTION: FOR YOUR OWN SAFETY; Read and follow all of the Safety and Operating instructions before Operating this Dust Collector. Customer Helpline 1-800-897-7709 Please have your Model No. and Sedal No. available. Sears, Roebuck and Co., Hoffman Estates, JL (}0179 U.S.A. Part No. OR92136 Revision A Espa5olpg. 21 SECTmON PAGE Warranty ..................................................................................... 2 Product Specifications .....

-Route the hose as shown in figure 11. Place the metal pressure tube in position on the fitting on top of control valve. Secure with the compression nut on the pressure tube, using an adjustable wrench. Make certain the metal pressure tube is positioned so that the pressure hose is above the slide plate as shown. FINAL ASSEMBLY • Make certain all nuts, bolts and hose clamps are tightened securely. • Before operating the log splitter, make certain to follow the “Initial Preparation” instructio

To maintain balance on abrasive wheel points, before each use, with the wheel point secured in the collet, turn on the Rotary Tool and run the Dressing Stone lightly against the revolving wheel point. This removes high spots and trues up the wheel point for good balance. The hanger is provided for the use of hanging your tool while using the flex-shaft or for storage. If you do not use the hanger, remove it from the tool and snap it back into place underneath the cord so it will be out of the wa

Los accesorios pueden resultardafiadosduranteeltransporteo elmanejoy puedensalir despedidos al ganar velocidad. Esto no escornish,perosf sucede. Practiqueprimero enmaterialesde desechoparaver c6mocorta laherramientagiratoria.Tengaencuenta queel trabajo es realizadopor la velocidad deta Paratenermejor controlal realizartrabajofino, agarre laherramientagiratoriacomo unI_pizentreeldedo pulgary eldedo indice. herrarnientay porelaccesorioqueseencuentraenel portaherramienta. Usted no debe apoyarsesobr

° Espa_ol Sears, Roebuck and Co., Hoffman Estates, IL 60179 2610913327 Table of Contents Page Warranty ........................................................ 2 Power Tool Safety Rules .......................................... 3-6 Symbols ........................................................ 7 Functional Description and Specifications ............................ 8-9 Assembly .................................................... 10-11 Operating Instructions ..................................

DUST COLLECTION S YS TEM FOR YOUR SAFETY: ° assembmy READ ALL INSTRUCTIONS ooperation CAREFULLY. "parts o repamr Sold by SEARS, ROEBUCK AND CO., Chicago, IL. 60684 U.S.A. Part No. SP5373 Printed in Taiwar_ • • •:• •_:-•-::_:/.'-• ••• ,.,. ,,i _. FULL:ONEYEAR WARRANTY ON CRAFTSMAN DUST C-OLL_ If within 0ne year from the date of purchase, thls Craftsman Dust Collection System falls due to a defect in maierlal0r workmanship;Searswil!repair it,freeofcharge; WARRANTY SERVICEIS AVAILABLE BY SIMPLY CON

Figure 7 -Attaching Inlet ATTACH HOSE Refer to Figure 8. Hose needs to be attached to the inlet using hose clamp. To attach hose: • Slide hose clamp onto one end of hose. Loosen clamp screw if required to slide hose clamp onto hose. • Position the hose clamp wires on the hose grooves. • Slide hose with clamp onto inlet. • Tighten hose clamp screw to secure hose with inlet. • Slide other hose clamp onto the opposite hose end. This end will be connected to the dust producing machine Figure 8 -Atta