valutazioni - 1, GPA: 3
(
)
)
|
Facilità d'uso
PICTURE MODE Remote control Control panel ..See “Navigating through the MENU” on page 27. ..See “Main menu and Sub-menu” on page 28. COLOR TINT Darker Lighter Settings Depending on the projection environment, you can use these preset parameter settings to optimise image projection. Press IH to cycle through the options. STANDARD Setting for a general image DYNAMIC Bright and sharp setting BLACKBOARD Setting for when projecting on a blackboard See “BLACKBOARD” on page 36. NATURAL Reproduces the original color of the image NOTE: • It may take for a while until the selected mode is stabilised. • When FUNCTION BUTTON is set to "PICTURE MODE" (see “FUNCTION BUTTON” on page 34), the PICTURE MODE operation can also be carried out by pressing the FUNCTION button at the front of the projector. CONTRAST You can adjust the contrast of the projected image. Adjust the BRIGHTNESS in advance if necessary. Lower Higher BRIGHTNESS You can adjust the brightness of the projected image. Darker Brighter (NTSC/NTSC 4.43/COMPONENT signals only) You can adjust the skin tone in the projected image. More greenish More reddish SHARPNESS You can adjust the sharpness of the projected image. More Less sharp sharp COLOR TEMPERATURE You can adjust the white balance of the projected image. • LOW More bluish • STANDARD Balanced white • HIGH More reddish Projecting sRGBcompatible pictures sRGB is an international color reproduction standard (IEC61966-2-1) established by the International Electrotechnical Commission (IEC). If you would like the colors in sRGB-compatible pictures to be reproduced more faithfully, make the following settings. 1. Press the F or G button to select “PICTURE MODE”, and then press the I or H button to select “NATURAL”. 2. Press the DEFAULT button on the remote control unit. 3. Press the F or G button to select “COLOR TEMPERATURE”, and then press the I or H button to select “STANDARD”. NOTE: • sRGB is only enabled when RGB signals are being input (when “LAMP POWER” is set to “STANDARD”, “AI” is set to “OFF”, and “DAYLIGHT VIEW” is set to “OFF”). ENGLISH - 30 PICTURE menu DAYLIGHT VIEW DETAILED SETUP You can keep the projected image bright and vivid even in well-lit rooms where the ambient light sources cannot be controlled, such as when a door opens or when window coverings fail to block out sunlight. • AUTO: Automatic adjustment • OFF: Deactive NOTE: • Do not cover the Luminance Sensor of the projector. See “Luminance Sensor” on page 12. • AUTO is not available when INSTALLATION setting in OPTION menu is set to REAR/DESK or REAR/ CEILING. AI The lamp is controlled according to the input signals to project images with the best quality. • ON: Active • OFF: Deactive NOTE: •“AI” is disabled when “LAMP POWER” is set to “ECOMODE”. See “LAMP POWER” on page 34. You can perform more detailed image adjustment manually. • For RGB signals • WHITE BALANCE You can adjust the white balance more properly in 3 colors temperature by pressing IH. • WHITE BALANCE RED • WHITE BALANCE GREEN • WHITE BALANCE BLUE • For S-VIDEO/VIDEO signals • TV-SYSTEM When the video signal is changed, the setting switches automatically. You can switch the setting manually to match the video data. Press IH to cycle through the options. AUTO NTSC SECAM NTSC 4.43 PAL-N PAL PAL-M NOTE: • AUTO setting will select from NTSC/NTSC 4.43/PAL/ PAL60/PAL-M/PAL-N/SECAM. • STILL MODE You can reduce the vertical flicker when projecting a still image. • OFF: Deactive • ON: Active Settings NOTE: •Set to OFF when projecting a moving image. • NOISE REDUCTION You can switch the automatic noise reduction system on/off. Press IH to select the required setting. • ON: Automatic noise reduction • OFF: No noise reduction NOTE: • Applying noise reduction may affect image quality. ENGLISH - 31 POSITION menu (S-VIDEO/VIDEO/COMPUTER/COMPONENT signals only) You can move the projected image for fine adjustment. Press IH to move horizontally and FG vertically. REALTIME KEYSTONE Remote control Control panel ..See “Navigating through the MENU” on page 27. ..See “Main menu and Sub-menu” on page 28. POSITION DOT CLOCK POSITION H V Image Operation NOTE: • You can correct the distortion ± 30 degrees from the plane. For a better quality image, installing the projector with a minimum of distortion is recommended. • The distortion of the Main menu screen is not correctable. • The result of the keystone correction will affect the aspect ratio and the size of the image. • You can correct the keystone distortion manually when “REALTIME KEYSTONE” is set to “ON”. However, when you turn on the power, the amount of correction will be reset and “REALTIME KEYSTONE” will function again if the tilt is different from the last time you used the projector. If you correct the keystone distortion manually when “REALTIME KEYSTONE” is set to “OFF”, the amount of correction will be stored by the projector even after the power is turned off. NOTE: • If the projecting signal’s dot clock frequency is higher than 100 M...