valutazioni - 3, GPA: 3.7
(
)
)
|
Foto e specifiche Sony VPL-EW5 |
da questo dispositivo ha anche altre istruzioni :
Facilità d'uso
The setting mode will be temporarily changed to “Manual” from “Auto”. If you want restore the “Auto” setting, first switch the V Keystone setting to “Manual”, then return it to “Auto”. • When you want to apply the fine adjustment value the next time, change the V Keystone setting to “Manual” from “Auto”. Adjustments and Settings Using a Menu The INSTALL SETTING Menu The INFORMATION Menu The INFORMATION menu displays the model name, serial number, the horizontal and vertical frequencies of the input signal and the cumulated hours of usage of the lamp. Model name Serial number Memory number of an input signal Signal type fH: 48,47kHz fV: 60,00Hz No.23 1024x768 Lamp Timer: 2 H VPL-EX50 INFORMATION Input A Setting items Functions fH Displays the horizontal frequency of the input signal. The displayed value is approximate. fV Displays the vertical frequency of the input signal. The displayed value is approximate. Lamp Timer Indicates how long the lamp has been turned on. Note These are only displayed on the screen. You cannot alter the display, and these is no setting to be altered. The INFORMATION Menu Input signals and adjustable/setting items Some of the items in the menus cannot be adjusted depending on the input signal as indicated in the following tables. The items that cannot be adjusted are not displayed in the menu. Adjust Picture... menu z : Adjustable/can be set – : Not adjustable/cannot be set *1: Except for preset memory No. 7, 8 *2: Cannot be set in the Presentation mode INPUT SETTING menu Item Input signal Video or S-Video (Y/C) Component Video GBR Computer B&W Picture Mode z z z z z Adjust Picture... Contrast z z z z z Brightness z z z z z Color z z z – – Hue z (NTSC 3.58/4.43 only) z z – – Sharpness z z z – z Gamma Mode – – – z – Color Temp. z z z z*2 z DDE z z (Interlace format only)*1 z (Interlace format only)*1 – z Volume z z z z z Adjustments and Settings Using a Menu Item Aspect Adjust Signal Dot Phase H size Shift Video/S-Video (Y/C) Component Video GBR Computer z z z z*3 – – – z – – – z – z z z z : Adjustable/can be set – : Not adjustable/cannot be set *3: Can be set except preset memory number 49. Input signal The INFORMATION Menu B Maintenance Replacing the Lamp The lamp used as a light source is consumable product. Thus replace the lamp with a new one in the following cases. • When the lamp has burnt out or dims • “Please replace the Lamp.” appears on the screen • The LAMP/COVER indicator lights up (repeats flashing three times) The lamp life varies depending on conditions of use. Use an LMP-E190 Projector Lamp as the replacement lamp. Use of any other lamps than the LMP-E190 may cause damage to the projector. Notes • If the lamp breaks, ask qualified Sony personnel to replace the lamp and to check inside. • Pull out the lamp by holding the handle. • When removing the lamp, make sure it remains horizontal, then pull straight up. Do not tilt the lamp. If you pull out the lamp while it is tilted and if the lamp breaks. 1 Turn off the projector, and disconnect the AC power cord from the AC outlet. Note When replacing the lamp after using the projector, wait for at least an hour for the lamp to cool. 2 Place a protective sheet (cloth) beneath the projector. Turn the projector over so you can see its underside. Note Be sure that the projector is stable after turning it over. 3 Open the lamp cover by loosening the screw with a Phillips screwdriver. Note For safety reasons, do not loosen any other screws. 4 Loosen the two screws on the lamp unit with the Phillips screwdriver (a). Fold out the handle (b), then pull out the lamp unit by the handle (c). Handle Replacing the Lamp 5 Insert the new lamp all the way in until it is securely in place (a). Tighten the two screws (b). Fold down the handle to replace it (c). Notes • Be careful not to touch the glass surface of the lamp. • The power will not turn on if the lamp is not secured properly. • Do not allow any liquid or other objects into the slot to avoid electrical shock or fire. 6 Close the lamp cover and tighten the screw. Note Be sure to attach the lamp cover securely as it was. If not, the projector cannot be turned on. 7 Turn the projector back over. 8 Connect the power cord. The ?/1 key lights in red. 9 Press the ?/1 key to turn the projector on. 10Press the MENU key, and then select the Setup menu. 11Select “Lamp Timer Reset”, and then press the ENTER key. SET SETTING Input-A Smart APA: On Auto Input Search: Off Input-A Signal Sel.: Auto Color System: Auto Power Saving: Off IR Receiver: Front & Rear Panel Key Lock: Off Lamp Timer Reset 12Select “Execute” with the V key, and then press the ENTER key. The Lamp Timer is initialized to 0, and “Change the Lamp and clean the Filter?” is displayed in the menu screen. Change the Lamp and clean the Filter? Yes: No: Refer to page 44 for “Cleaning the Air Filter”. 13Select “Yes” with the v key. “Lamp Timer Reset Complete!” is displayed in the menu screen. Disposal of the used lamp For the custome...