valutazioni - 1, GPA: 4
(
)
)
|
Facilità d'uso
CALL Press CALL. The information described below is displayed. The information display turns off when the CALL button is pressed again. Status display Input - current input source H-resolution - the horizontal resolution of the input signal (at RGB input) V-resolution - the vertical resolution of the input signal (at RGB input) H-frequency - the horizontal frequency of the input signal (at RGB input) V-frequency - the vertical frequency of the input signal (at RGB input) Sync - the polarity of the sync signal (at RGB input) Video mode - the color mode of the video signal (at Video, S-Video input) Signal format - the formatting of the Y/PB/PR signal (at Y/PB/PR input) Lamp time - the elapsed usage time of the lamp Version - the version of the firmware Shutter - the shutter speed of the document imaging camera (at document imaging camera input) Notes • The information displayed is not refreshed even if it changes. To refresh the information, turn off the information display, then turn it back on. • The information display turns off if any other operation is performed. • The “Lamp time” shows an approximate time for lamp replacement. (It should not be used as a lamp warranty time counter.) If the time indicated here nears 1500H, contact your store of purchase about obtaining a replacement lamp (TLPL55, sold separately). • The “Lamp time” can be reset when the lamp is replaced. • The “Version” is the version of the control program used in the projector and is used for servicing, etc. Operations Operating the presentation mode CONTENTS 41 You can change the slide, for the presentation on the computer, by using the remote control when connecting the projector to the computer with the supplied USB cable. Operations Notes • This function is available with O.S (operating system) of Windows 98/98SE, Windows Me, Windows 2000, Windows XP or Mac OS9 with a USB port as standard. • When connecting to the computer’s USB port for the first time, a message asking you to insert the Windows98 or Windows 98SE CD-ROM may appear on the computer’s monitor screen, depending on whether or not the device driver is installed. If so, do as the message says. • When using a USB cable other than the supplied one, be sure to use a shielded type. USB AUDIO IN CONTROL VIDEO IN To USB connector Be sure to connect in the proper direction. USB cable (supplied) Computer for presentation To USB port USB connector 1 Connect a computer to the projector with the supplied USB cable. Also connect the RGB cable and the audio cable if necessary. 23 2 Start a presentation on the computer. • In case of Microsoft ® PowerPoint ®, start the slide show to make a state of displaying the first slide. • In case of Adobe® Acrobat ® or AcrobatReader®, make state that [Full Screen] is selected from [View] menu. • This function is also available in other application software that can change a slide by pressing , of a computer. Continued CONTENTS 42 Operating the presentation mode (continued) Remote control MENU ON / INPUT ENTER CT-90106 KEYSTONE AUTO SET EXIT / P.MODE PIP FREEZE MUTE CALL RESIZE VOL / ADJ STANDBY3 6 5,7 3 P.MODE KEYSTONE AUTOSET EXIT ON / STANDBY VOL / ADJ ENTER MENU INPUT FANTEMPLAMPON Control panel (Main unit side) Operations Adjust the projector before presentation if necessary. In the presentation mode after step 5, the projector cannot be adjusted. 4 3 5 Press P.MODE and hold for two seconds. The projector enters into the presentation mode. The icon appears in the presentation mode. Select the computer input with INPUT. You can change the order of procedure 1 to 3. INPUT INPUT P.MODE Change a slide with the selection buttons ( / ). : Advancing to the next slide. : Returning to the previous slide. • The selection buttons of the main unit can not be used. • The slide can not be switched even if you press and hold the selection buttons continuously. (The function is different from the , keys of the computer.) 6 7 When the presentation is finished; To exit the presentation mode, press P.MODE. The projector returns to the normal mode. P.MODE 4343 Operating the menu screen CONTENTS Various adjustments and settings can be made on the menu screen. The basic operations on the menu screen are shown here. GUIDE MENU: You can adjust or set the functions used frequently. FULL MENU: For the operating instruction, refer to the next page. Start 44 Adjustments &Settings FULL Item Next Quit Adjust the image brightness. Select the image with its brightness priority or quality (color) priority. Correct the keystone distortion of the screen. Select the input source when changing the input. Adjust the image flicker. EXITENTERMENU GUIDE MENU Analog RGB Items Button operation guide The current input source Press MENU. Then GUIDE MENU appears. (Then FULL MENU appears if the latest operation had been finished with the FULL MENU and afterwards power is not turned off.) When you make more detailed adjustments and settings, call the FULL MENU. Return to the GUIDE MENU when...
Questo manuale è adatto anche per i modelli :Proiettori - Conference Room Projectors TLP-561 (1.98 mb)
Proiettori - TLP-560 (1.98 mb)
Proiettori - TLP-561 (1.98 mb)