valutazioni - 0, GPA: 0
(
)
)
|
Facilità d'uso
Set your computer to output the signal to only the external monitor. For details, refer to the computer’s operating instructions supplied with your computer. • This projector is compatible with a DDC2B (Digital Data Channel 2B). If your computer is compatible with a DDC, turn the projector on according to the following procedures. 1 Connect the projector to the computer by using the supplied HD D-sub 15 pin cable. 2 Turn the projector on. 3 Start the computer. Setting Up and Projecting 17 17 GB Connecting the Projector To connect an IBM PC/AT compatible computer INPUT AS VIDEOVIDEOAU MONITOR OUT to audio output Left side HD D-sub 15-pin cable (supplied) Stereo audio connecting cable (not supplied)a) to monitor output Computer a) Use a no-resistance cable. To connect a Macintosh computer To connect a Macintosh computer equipped with video output connector of a type having two rows of pins, use a commercially available plug adaptor. GB 18 Connecting the Projector Connecting with a VCR or 15k RGB/Component Equipment This section describes how to connect the projector to a VCR and 15k RGB/ component equipment. For more information, refer to the instruction manuals of the equipment you are connecting. To connect a VCR Setting Up and Projecting DIO AUDI O INPUT AS VIDEOVIDEO MONITOR OUT Stereo audio connecting cable (not supplied)a) VCR to S video output Left side to audio output Video cable (not supplied) or S-Video cable (not supplied) to video output a) Use a no-resistance cable. To connect a 15k RGB/Component equipment DIOAU I INPUT AS VIDEOVIDEO MONITOR OUT Left side Stereo audio connecting cable (not supplied)a) SMF-402 Signal Cable (not supplied) HD D-sub 15-pin (male) - 3 . phono jack to audio output 15k RGB/Component equipment to RGB/ component output a) Use a no-resistance cable. 19 19 GB Connecting the Projector Notes Notes • Set the aspect ratio using “Wide Mode” in the INPUT SETTING menu according to the input signal. • When you connect the unit to 15k RGB or component video equipment, select video GBR or component with the “Input-A Signal Sel.” setting in the SET SETTING menu. • Use the composite sync signal when you input the external sync signal from 15k RGB/component equipment. Connecting with a Monitor Equipment This section describes how to connect the projector to a monitor equipment. For more information, refer to the instruction manuals of the equipment you are connecting. AU DIO INPUT AS VIDEOVIDEO MONITOR OUT Left side Monitor cable (not supplied) HD D-sub 15-pin (male) - HD D-sub 15-pin (male) to monitor input Monitor equipment GB 20 Connecting the Projector Selecting the Menu Language You can select one of thirteen languages for displaying the menu and other on- screen displays. The factory setting is English. To change the menu language, proceed as follows: Setting Up and Projecting INPUT MENU PUSH ENTERTILT Remote control detector 1Plug the AC power cord into a wall outlet. 2Press the I / 1 key to turn on the projector. 3Press the MENU key. The menu appears. The menu presently selected is shown as a yellow button. PICTURE SETTING Picture Mode: Standard Adjust Picture... Volume: 30 Input A 21 21 GB Selecting the Menu Language 4 Press the v or V key to select the MENU SETTING menu, then press the B or ENTER key. The selected menu appears. Input A : : : : A 5 Press the v or V key to select “Language,” then press the B or ENTER key. Input A : : : : 6 Press the v, V, b or B key to select a language, then press the ENTER key. The menu changes to the selected language. To clear the menu Press the MENU key. The menu disappears automatically if a key is not pressed for one minute. GB 22 Selecting the Menu Language Projecting Setting Up and Projecting INPUT MENU PUSH ENTERTILT ON/STANDBY indicators Remote control detector 1 Plug the AC power cord into a wall outlet, then connect all equipment. The ON/STANDBY indicator lights in red and the projector goes into standby mode. 2 Press the I / 1 key. The ON/STANDBY indicator lights in green and the Intelligent Auto-setup starts. The lens protector opens, and the powered tilt adjuster rises and stops at the previously adjusted position. 3 Turn on the equipment connected to the projector. Depending on the type of your computer, for example a notebook, or an all-inone LCD type, you may have to switch the computer to output to the projector by pressing certain keys (e.g., , etc.), or by changing your computer’s settings. VGA LCD / /, 23 23 GB Projecting Fx:“x” indicate an optional numerical value. The Fx key varies depending on a computer’s makers. F7 Fx Fn or 4 Press the INPUT key to select the input source. To input from Press INPUT to display Computer connected to the INPUT A connector INPUT A Video equipment connected to the VIDEO input connector VIDEO Video equipment connected to the S VIDEO input connector S VIDEO Smart APA (Auto Pixel Alignment) adjusts the picture of the connected equipment so that it is projected clearly. Notes • If “Auto Input ...