valutazioni - 0, GPA: 0
(
)
)
|
Facilità d'uso
0.975 b = x – (SS/0.9055 . 6.912) c = x – (SS/0.9055 . 6.912 + 83.4) 34 (GB) 35 (GB) Notes for Installation Unsuitable Installation Do not install the projector in the following situations. These installations may cause malfunction or damage to the projector. Poorly ventilated •Allow adequate air circulation to prevent internal heat build-up. Do not place the unit on surfaces (rugs, blankets, etc.) or near materials (curtains, draperies) that may block the ventilation holes. When internal heat builds up due to blockage of the ventilation holes, the temperature sensor may function, a warning message will be displayed, and the power may be turned off automatically after one minute. • Leave space of more than 50 cm (19 3/4 inches) around the unit. • Be careful that the ventilation holes do not inhale tiny objects such as pieces of paper. Highly heated and humid •Avoid installing the unit in a location where the temperature or humidity is very high, or the temperature is very low. • To avoid moisture condensation, do not install the unit in a location where the temperature may rise rapidly. Very dusty Avoid installing the unit in a location where there is a lot of dust; otherwise, the air filter will clog. The dust blocking the air through the filter may cause the internal heat level of the projector to rise. Clean the filter periodically. Unsuitable Conditions for Use Do not do any of the following. Toppling the unit Avoid standing the unit on its side as the unit may topple over. This may cause a malfunction. Tilting the unit more than 15 degrees Avoid tilting the unit at an angle of more than 15 degrees. Installation of the unit in this manner may cause a malfunction. PUSH PUSH Notes for Installation Installation Notes for Installation Blocking the ventilation holes Avoid using something that covers over the ventilation holes (exhaust/intake); otherwise, the internal heat level may build up. Removing the adjusters Avoid using the unit with the adjusters removed. Blocking the ventilation holes (intake) may cause internal heat build-up. 36 (GB) Maintenance 3 Loosen the screws on the lamp unit with theMaintenance Phillips screwdriver. Notes Maintenance • If the lamp breaks, consult with qualified Sony personnel. • Pull out the lamp unit by holding the handle. If you touch the lamp unit, you may be burned or injured. •When removing the lamp unit, make sure it remains horizontal, then pull straight up. Do not tilt the lamp unit. If you pull out the lamp unit while it is tilted and if the lamp breaks, the pieces may scatter, causing injury. Replacing the Lamp When the lamp has burnt out or dims, or “Please replace the LAMP.” appears on the screen, replace the lamp with a new one. The lamp life varies depending on conditions of use. The message appears after 1500 hours of use. Use an LMP-P202 Projector Lamp as the replacement lamp. When replacing the lamp after using the projector Turn off the projector, then unplug the power cord. Wait for at least an hour for the lamp to cool. Note The lamp remains at a high temperature after you turn off the projector with the I / 1 key. If you touch the lamp, you may burn your finger. When you replace the lamp, wait for at least an hour for the lamp to cool. 1 Place a protective sheet (cloth) beneath the projector. Hold the projector handle and place the projector face down. Note When replacing the lamp, be sure the projector is on a flat and stable surface. 2 Slide open the lamp cover after loosening its screw with a Phillips screwdriver. 4 While holding the handle and keeping the lamp unit horizontal, pull straight up. 5 Insert the new lamp all the way in until it is securely in place. Tighten the two screws. Fold down the handle. Notes •Be careful not to touch the glass surface of the lamp. • The power will not turn on if the lamp is not secured properly. 6 Close the lamp cover and tighten the screw. 7 Turn the projector back over. 8 Connect the power cord and turn the projector to the standby mode. 9 Press the following keys on the control panel in the following order for less than five seconds each: RESET, <, ,, ENTER. 37 (GB) Maintenance Notes •Be sure to use an LMP-P202 Projector Lamp for replacement. If you use lamps other than the LMPP202, the projector may malfunction. •Be sure to turn off the projector and unplug the power cord before replacing the lamp. •Do not put your hands into the lamp replacement socket, and do not allow any liquid or objects to fall into it to avoid electrical shock or fire. Disposal of the used lamp As the used lamp contains Mercury, dispose of the lamp according to local, state or federal laws. As the materials used in this lamp are similar to those of a fluorescent lamp, you should dispose of a used projector lamp in the same way as a fluorescent lamp. Cleaning the Air Filter The air filter should be cleaned every 300 hours. When it becomes difficult to remove the dust from the filter, replace the filter with a new one. To clean the air fil...
Questo manuale è adatto anche per i modelli :Proiettori - VPL-PX10 (1.65 mb)
Proiettori - VPL-PX15 (1.65 mb)