valutazioni - 0, GPA: 0
(
)
)
|
da questo dispositivo ha anche altre istruzioni :
Proiettori - S5201M (1.26 mb)
Proiettori - S5201M (1.2 mb)
Facilità d'uso
Using Wireless Acer SmartPen
Preparations
Charging the battery
1.
To charge the battery, open the flap on the back of the pen to
expose the USB connector.
USB
2.
Take a USB cable, and connect the smaller end to the pen and the
larger end to a computer. Make sure the computer is powered on.
3.
The battery light stays on while the battery is charging. When
D-Sub
charging is finished, the battery light is off. You can disconnect
the USB cable or keep it connected.
Other notes about using the Acer SmartPen
USB Type A
VGA
1.
Keep the pen vertical to the projection screen. The best pointing
to USB mini-B
cable
accuracy can be achieved by doing so.
cable
2.
Avoid standing too far from the screen. The closer you are to the
D-Sub
screen, the better performance the pen has.
USB
3.
Hold the pen the way you hold a remote control or a pen.
4.
A full battery charge takes 6-8 hours and will allow 20-40 hours
Power
non-stop use. The battery is only rechargeable, and is not user
cord
serviceable or user replaceable.
MIC.
5.
Avoid shadows! The pen cannot
DC OUT
work if its tip is in a shadow or it is
pointing at a shadow.
6.
Keep the pen within 20m to the
projector and within 8m to the
screen for best performance.
1.
Ceiling mount the projector and connect the projector
7.
For the scroll wheel and Power
with your computer using a USB Type A to USB Mini-B cable which
point functions, please refer to the
has a length limit of 5 meters. Please use a powered USB hub for
CD manual.
extension.
8.
When the SmartPen function is
2.
Turn on your projector and make sure it is displaying the
enabled, the 3D function and color
computer’s image (VGA, HDMI or LAN signal with native
setting adjustment in the OSD menu will become unavailable.
resolution).
3.
Enable the pen by selecting "Enable" in the Setting > Acer
Troubleshooting
SmartPen > Pen Function menu. The pen’s link light starts to blink.
1.
If the pen does not work at all, or it works intermittently, try one
4.
Point the pen at the screen to point, click, and drag.
of these solutions:
Overview of the Acer SmartPen
• Try holding down one of the pen’s buttons while moving the
pen.
Tip
• Press the tip, L, or R button on the pen to turn it on.
Left mouse button
Sensor
• If the pen’s green Link light never blinks, then the pen’s battery
Right mouse button
is fully discharged; connect the pen to your computer by using a
Wheel button
USB cable.
Link light
Battery light
• Make sure the pen is not pointing at a shadow or its tip is not in
a shadow.
• If the room is brightly lit, reduce the room illumination.
USB connector
• Point the pen away from the screen while using the computer’s
mouse.
• If someone is using a different pen with the same projector,
Using the Quick Interactive Pen Function menu
they must stop using it before you can use your own.
• Reset the pen by pushing the end of a paper clip into the reset
1.
Simply click the wheel button to activate the menu.
opening on the pen.
2.
Rotate the wheel button to select a desired function from among
2.
If the mouse pointer is in the wrong place on the screen, or the
Off, Alt+F4, Enter, Home, Page Up, and Page Down.
mouse pointer’s movement is restricted to only part of the screen,
3.
To perform the function, click the wheel button again.
try one of these solutions:
Battery Light
• Make sure your projector is displaying the computer’s screen
The amber battery light shows the status of the wand's built-in battery.
and not some other source (such as DVD, VCR, etc.). To change
The battery light will turn on while the wand is charging, and it will blink
the source, press the Source button on the projector or its
if the battery is low (2-4 hours of wand use left).
remote control.
Link Light
• Make sure the projector is displaying the same image as the
The blue link light shows the status of the wand's wireless connection to
computer’s main or built-in monitor (do not extend your
the projector. The link light will blink frequently (more than once per
desktop into multiple monitors.)
second) when the wand is attempting to link to the projector; then it will
3.
If the battery light does not turn on when the pen is being
blink less frequently (about once every 4 seconds) after the wand has
charged, try one of the following:
linked to the projector. The link light will stay off when the wand is off.
• Make sure a USB cable is connected between the pen and your
Turning off the Acer SmartPen
computer. And your computer is powered on.
You can turn off the Acer SmartPen by either of the methods below:
• Disconnect the SmartPen by not pointing at the screen and not
pressing any button for one minute and the SmartPen will go
into sleep mode. To wake up the SmartPen, simply point it at
the screen or press any button.
• Turn off the SmartPen function in the OSD menu. (Setting >
Acer SmartPen > Pen Function > Disable)
• Press and hold the right mouse button on the SmartPen for
three seconds to force the SmartPen to disconnect from the
projector.
P/N:4J.14802.021
...