valutazioni - 1, GPA: 5
(
)
)
|
Facilità d'uso
Australia 1300 889 785 Mon-Fri 8am – 6pm AEST New Zealand 0800 67 42 66 Mon-Fri 10am – 8pm NZST General Information General Information WARNING It is very important that you read the User Guide carefully as it contains detailed information on installation, programming and operational issues which you will need to be aware of to ensure the Care Phone operates properly. Following is a list of some of the important issues and important warnings which you need to be aware of. This is a summary of the important issues you must still read the User Guide in full. • Thetelephoneisdesignedforindooruseonly.Donotinstall the telephone in areas where there is the risk of an explosion, excessive exposure to smoke, dust, vibrations, chemicals, moisture and heat. •Donotuseyourtelephoneduringanelectricalthunderstorm as it is possible to get an electric shock. Refer to information contained in Telstra White pages directory. • Theearpieceofthehandsetmayattractsmallmetalobjects such as staples and pins. Care should be taken when placing the handset near these items. • Settingthereceivervolumetomaximummay,undersome situations cause ear damage. We suggest returning the handset volume control to the “0” position after each call. • Donotinstallindamplocationssuchasabathroomor laundry, do not expose the unit to direct sunlight. General Information Notes for operation in New Zealand The grant of a Telepermit for any item of terminal equipment indicates only that Telecom has accepted that the item complies with the minimum conditions for connection to its network. It indicates no endorsement of the product by Telecom, nor does it provide any sort of warranty. Above all, it provides no assurance that any item will work correctly in all respects with another item of Telepermitted equipment of a different make or model, nor does it imply that any product is compatible with all of Telecom’s network services. This equipment shall not be set to make automatic calls to the Telecom “111” Emergency Service. This equipment may not provide for the effective hand-over of a call to another device connected to the same line. This equipment should not be used under any circumstances that may constitute a nuisance to other Telecom Customers. If the "send" switch is used to boost or cut the send volume of a call, it must be returned to the "0" position after that call. REN (RN for New Zealand) The REN (Ringer Equivalence Number) or (RN) is of significance only if you wish to connect more than 1 telephone to your telephone line. A standard telephone line has a maximum REN capacity of 3 (RN of 5). It is possible to connect 3 devices with a REN of 1 (RN of 1) with no degradation to the product’s performance. Exceeding this limit may cause the volume of the ringer in any phone to decrease or not ring at all. 4 Installation Installation Desk Mounting Fit the bracket as shown in the illustration. Insert the brackets three tabs into the matching slots on the bottom of the phone and click into place. Wall Mounting 1. Fit the bracket as shown in the illustration. Insert the brackets three tabs into the matching slots on the bottom of the phone and click into place. 2. Drill two holes vertically, one above the other, 83mm apart, and leave the screws protruding from the wall by 5mm. 3. Turn around the hanging peg (located by the hook switch) for 180 degrees, so it will hold the handset in place when the phone is mounted on the wall. 4. Position the mounting holes on the base of the phone over the two protruding screws on the wall plate or on the wall. Gently push the phone flush against the wall plate then slide the phone downwards locking it into place. Connecting the Telephone 1. Plug one end of the curly cord into the socket on the handset. 2. Plug the other end of the curly cord into the left side of the phone. 3. Plug one end of the telephone line cord into the jack at the back of the base, and the other end into the wall socket. 4. Pick up the handset and listen for dial tone. NOTE: In Australia some phone wall sockets are the old “non modular” style. If you have this type of wall socket you will need to purchase a modular converter plug” (not supplied). These can be obtained from electronic stores. Bracket position for desk mounting Bracket position for wall mounting 5 Location of Controls 1 2 3 10 9 11 4 5 6 7 8 12 13 6 Location of Controls Location of Controls 1. Hook switch 2. Handset holder 3. Boost button 4. Ring LED indicator 5. Store button 6. Recall button 7. Redial button 8. Speakerphone button 9. One touch button (M1-M19) 10. Keypad 11. Mute button 12. Speakerphone volume 13. Coil cord socket 14. Ring Tone Hi/Mid/Low switch 15. Recall Time Switch 16. Ringer Hi/Low/Off switch 17. Sending switch 18. Telephone line socket 19. Handset Tone control 20. Handset volume control 19 20 14 15 16 17 18 Operation Operation Recall switch Setting For Australia the Recall switch should be set to 100. For New Zealand the Recal...