valutazioni - 2, GPA: 3
(
)
)
|
Facilità d'uso
Warning: Dispose of dead batteries promptly and properly. Do not bury or burn them. Replacing the Batteries When BATT appears or the display dims, replace the batteries. 1. Unplug both modular line cords from the back of the system, then wait a few seconds. 2. Follow Steps 1-4 of “Installing Batteries.” 3. Reconnect the modular line cords. CONNECTING THE SYSTEM Your system connects to any modular phone jack and phone. You can also connect it to an answering machine. Your system is designed to be connected to the telephone network using a compatible modular jack that is compliant with Part 68 of FCC Rules. The USOC number of the jack to be installed is RJ11C (for both telephone line jacks). Connecting to a Single-Line Phone 1. Disconnect the telephone line cord from the phone and plug it into the system’s TO LINE jack. 2. Plug one end of the supplied line cord into the system’s TO PHONE jack. 3. Plug the other end of the cord into the phone’s jack. Connecting to a Two-Line Phone To record information about calls received on a two-line phone, you can connect two systems using a triplex adapter (not supplied), available at your local RadioShack store. Each system only records information about calls received on the line to which it is connected. L1 L2 L1+2 Triplex Adapter Systems Follow these steps to connect two systems to a two-line phone. 1. Disconnect the telephone line cord from the modular phone jack on the wall and plug it into L1 + L2 on the triplex adapter. 2. Plug the triplex adapter into the modular phone jack. 3. Plug one end of the supplied line cord into the TO LINE jack on one of the systems. 4. Plug the other end of the cord into either L1 or L2 on the triplex adapter. 5. Repeat Steps 3 and 4 to connect another system to the other jack (L1 or L2) on the triplex adapter. Connecting to an Answering Machine 1. Plug one end of the supplied telephone line cord into the modular wall jack. Then plug the other end into the system’s TO LINE jack. 2. Plug one end of another modular cord (not supplied) into the system’s TO PHONE jack. Plug the cord’s other end into the answering machine’s line jack. 3 3. Plug a third telephone line cord into the answering machine’s phone jack and the phone’s modular jack. Modular Wall Jack To Phone System Answering Machine 4. Set your answering machine to answer after two or more rings. This gives the system time to record the call information that the phone company sends between the first and second rings. MOUNTING THE SYSTEM You can set the system flat on a desk, shelf, or table or use the supplied mounting bracket to set the system at an angle. You can also use the bracket to mount the system to a wall. Attaching the Mounting Bracket 1. Align the keyhole slots on the bottom of the system with the hooks on the mounting bracket. 2. Gently push the bracket up into the system to secure it. To remove the bracket from the system, press up from the bottom of the system until the bracket snaps off. Mounting on Wall To mount the system on the wall, you need two screws (not supplied) with heads larger than the keyhole slots on the back of the mounting bracket. 1. Drill two holes 17/16 inches (37 mm) apart 1/8 at the mounting location. Thread a screw inch into each hole, letting the heads extend 17/16 about 1/8 inch (3mm) from the mounting inches surface. 1/8 2. Attach the mounting bracket to the system inch (see “Attaching the Mounting Bracket”). 3. Connect the system as described in “Connecting the System”. 4. Align the keyhole slots on the mounting bracket with the screws and slide the system down until it is secure. ADJUST THE DISPLAY CONTRAST To lighten or darken the display, hold down DELETE and REVIEW7 ::::# until CONTRASTADJUST appears. Then repeatedly press REVIEW 8 ;;;; to select the desired contrast setting. Press the REVIEW 7 ::::#key to set the contrast. CHOOSING A LANGUAGE Your system is programmed to display messages in English, but you can change it to display in French or Spanish. 1. Hold down REVIEW 7 ::::#and 8 ;;;; for about 3 seconds until the current language (ENGLISH, FRANCAIS for French, or ESPANOLfor Spanish) appears. 2. Repeatedly press REVIEW8 ;;;; until the desired language appears. 3. Press REVIEW 7 :::: to set the new language. Note: If a button is not pressed within 10 seconds, the time appears. SETTING THE TIME The time and date are set with your first incoming Caller ID and updated with every new call. To toggle between 12-or 24-hour time formats, repeatedly press DELETE while the system is not in use. RECEIVING AND STORING CALLS Caller ID is a service provided by your telephone company. When you subscribe to this service, the telephone company sends the caller’s telephone number (and name, if available) and the call’s date and time between the first and second rings. The system receives and displays this information for each call and updates the display with the current date and time. Your system saves up to 79 call records, then replaces the old...
Questo manuale è adatto anche per i modelli :Telefoni con filo - 2902 (61.96 kb)