valutazioni - 3, GPA: 3.7
(
)
)
|
Facilità d'uso
licensed to Advanced American Telephones. © 2000 Advanced American Telephones. All rights reserved. Printed in Mexico. 850003518 Issue 1AT&T 5/00 INSTALLATION................................. 3 Table/Desk Installation ......................... 4 Wall Installation .................................... 5 TELEPHONE OPERATION ................. 7 Making a Call ......................................... 8 Answering a Call ................................... 8 Line Status Lights .................................. 8 Redial .................................................... 8 Hold ...................................................... 8 Switching Between Lines During a Call ..................................... 9 Conference Calls ................................... 9 Conference Call Options....................... 9 Flash .................................................... 10 Temporary Tone .................................. 10 Ringer Volume ..................................... 10 Receiver (Handset) Volume ................. 10 CONTENTS TELEPHONE MEMORY ................... 11 Directory Card .................................... 11 Storing Memory Numbers .................. 11 Dialing Memory Numbers................... 11 Dialing Long Numbers ........................ 12 Erasing Memory Numbers .................. 12 IN CASE OF DIFFICULTY ................ 13 2 INSTALLATION NOTE: To use this product as a two-line phone, you must have either a two-line modular jack, or two separate one-line modular jacks. To use both lines of a two-line telephone, your local telephone company must provide two telephone numbers. 1 Install or replace the batteries (not included). • These batteries are needed to illuminate the line status lights. When battery power is low, the line status lights dim or don’t go on. CAUTION: Always unplug the line cord before installing batteries. • Turn the phone upside down, open the battery compartment door, and insert AAA batteries. Close the battery compartment door. NOTE: If you are connecting only Line 1 or only Line 2, use two batteries, as indicated on the bottom of the phone. If you are connecting both lines, use four batteries. 2 Set the dial mode. This telephone will work with touch tone or dial pulse (rotary) service. Even when set to dial pulse service the phone can be switched temporarily to tone mode for access to services that require tone signaling, including some tone-activated computer systems. To switch from pulse to tone dialing during a call, see “Temporary Tone” in the TELEPHONE OPERATION section of this manual. This phone comes set for touch tone dialing. Use the switch on the handset to select TT (tone) or DP (dial pulse), depending on your service. Touch tone dialing will not work if you have dial pulse service. INSTALLATION Table/Desk Installation Follow Steps 1 and 2 above. 3 Connect the long line cord(s) to the telephone. • If you have a two-line wall jack, use only the line cord with the clear modular plugs on each end. Plug one end into the jack labeled L1 OR L1/L2 on the bottom of the telephone. Thread the line cord through the groove on the bottom of the telephone so the set will lie flat on your table. • If you have two separate wall jacks, use both line cords. Insert one end of the cord with blue plugs into the jack labeled L1 OR L1/L2 on the bottom of the telephone. Insert one end of the cord with clear plugs into the jack labeled L2 on the bottom of the telephone. Thread the line cords through the groove on the bottom of the telephone so the set will lie flat on your table. L2 jack L1 or L1/L2 jack Thread line cord through groove so set lies flat on table 4 Connect the line cord(s) to your modular wall jack(s). • If you have a two-line jack, plug the free end of the line cord into the modular jack. Make sure the cord snaps firmly into place. • If you have two separate jacks, plug the free end of the cord with blue plugs into the modular jack for Line 1. Plug the free end of the cord with clear plugs into the modular jack for Line 2. INSTALLATION 5 Connect the handset to the telephone. Plug the coiled cord into the handset jack on the side of the phone. Plug the other end of the coiled cord into the handset. 6 Check for dial tone. Lift the handset, press L on the base, and listen for a dial tone. Then press lon the base. If you do not hear a dial tone, turn to IN CASE OF DIFFICULTY. 7 Confirm Lines 1 and 2. To determine which line is which, press Lon the base and call one of your telephone numbers. If you hear a busy signal, Line 1 is the number you called. If Line 2 rings, it is the number you called. Wall Installation Thread line cord through groove so set lies flat L2 jack L1 or L1/L2 jack Follow Steps 1 and 2 above. 3 Connect line cord(s) to telephone. • If you have a two-line wall jack, use only the short line cord. Plug one end into the jack labeled L1 OR L1/L2 on the bottom of the telephone. Thread the line cord through the groove on the bottom of the telephone. • If y...