valutazioni - 1, GPA: 4
(
)
)
|
Facilità d'uso
(Depending on the DSL provider’s recommendations, you may or may not want to use DHCP.) 4. Configure the Alti-IP 600H phone’s AltiWare address. 5. If NAT server is used, access NETWORK settings in the configuration menu. Change ENABLE NAT setting to YES and assign the NAT server’s public IP address in the NAT Address setting. 6. If configuring with an H.323 NAT router, the NAT router can forward IP traffic to a specified private IP address based on the destination port in the TCP/IP or UDP packets. When an H.323 endpoint is behind the H.323 NAT, you should set up the forwarding to a private IP address of this H.323 endpoint. If this H.323 endpoint is AltiWare, the NAT router must be configured to forward to following ports to the H.323 endpoints private IP address: • TCP port 10032 (for phone service) • TCP port 1720 (for H.225) • TCP/UDP 49152 ~ N (for H.245 and RTP/RTCP); where N = 49152 + (62 * number of VoIP boards) - 1. 7. Use #27 + ENTER to initiate logging onto AltiServ. 8. The phone will attempt to register as shown in the LCD screen. If the phone successfully passes through these stages, the phone shows the time and extension in the LCD screen and is now in normal operating mode. Note: The Alti-IP 600H AltiWare IP address, TFTP (IP) address and other network related configuration parameters will override the AltiAdmin’s settings when the phone registers with AltiServ. Other parameters will still be overridden by the AltiAdmin settings as before. Otherwise, refer to “Troubleshooting” on page 40. 9. Set up IP Phone properties in AltiWare as described in Step 2 - “AltiAdmin/ACM Admin Setup - AltiGen IP Phone Configuration Window” on page 9. Verifying the Phone Startup Process 1. All LED lights will be on. 2. The LCD screen displays [ATGN BOOT] on the first line. 3. On the second line of the LCD screen, the following messages are displayed in succession: —CHECK MEMORY (RAM checking state) —CHECK FW (Firmware checking state) —BOOTING NOW (Initialization of hardware - LCD, network, DSP, etc.) —INITIALIZING Resolving Errors Upon Startup • LED 1 light on = memory check failed • LED 2 light on = network failed • LED 3 light on = DHCP failed • LED 4 light on = attached IP address failed Active Logon While Another Handset is Already Logged On To the Same Extension Important:Also, the user should not use the VM option to logon the Alti-IP 600H. Restoring Default Settings 1. Press * * 7, then press the ENTER button 2. Press * * 2, then press the ENTER button. Rebooting the Alti-IP 600H Note: When the Alti-IP 600H is rebooted, the AltiWare IP address setting is set back to the original configuration. Configuring “Phone Setting” Soft Keys 1. Press * * 6, then the ENTER button. 2. Scroll to the program key to configure. 3. Enter the appropriate digits for the speed dial number or feature code. Dialing an IP Number Directly from the Alti-IP 600H Notes: • This only works when the Alti-IP 600H is operating in basic mode. • If the Alti-IP 600H is configured for a public IP address, you can call other public IP address devices. Headset Port Support Important:Contact AltiGen for the most current list of certified headsets. Pin 1 (Tx-), Pin 2 (Rx1), Pin 3 (Rx2), Pin 4 (Tx+) Note: For the Alti-IP 600H, if using Plantronics H91N or H101N headsets, in order to plug in these headsets to the headset port, a separate Plantronics cable should be used (and must be ordered separately: part # 27190-01). Operation Notes • When using #26 and #27 to log out/in, the Alti-IP 600H must be onhook. Using the speaker button to use #26 or #27 will not work. • Two dial tones are always heard when going offhook on the Alti-IP 600H. • If two calls ring into the Alti-IP 600H at the same time and the user attempts to answer the second call, the IP phone will automatically connect the user to the first call. • The user should reboot the Alti-IP 600H after disconnecting the LAN cable to the phone. • The user should reboot the Alti-IP 600H after changing the IP address or DHCP setting. • If the Alti-IP 600H is configured for a public IP address, you can call other public IP address devices. • If the Alti-IP 600H is configured for a private IP address, you can call other private IP address devices that you can “see” or that are on your subnet. • The daisy chaining of Alti-IP 600H phones is not supported. C H A P T E R 4 Configuring Phone Settings Important:Please note that the configuration in AltiAdmin will override the Alti-IP 600H phone’s local configuration after the IP Phone is registered. If the IP Phone’s local configuration is changed while in Basic mode, these changes will be overwritten by AltiAdmin settings. Also, after the IP Phone is successfully registered with AltiServ, the IP Phone will overwrite the AltiWare IP address and network-related settings on the server. Note: Several of these settings can be configured through AltiAdmin by the System Administrator. System Settings Network Settings Modifying DHCP Settings Enabling DHCP 1. Pr...