valutazioni - 3, GPA: 3.3
(
)
)
|
Facilità d'uso
Press when using a telephone or the EL25 to cancel programming sequence and exit programming mode. Page 7 Programming System Feedback / Responses (Beeps) The EL25 emits various audio tones to respond to input and to indicate certain conditions. Page 8 2 Short Beeps: Programming step was valid. 3 Short Beeps: Programming mode was exited. 1 Long Beep: Input was not valid. 2 Long Beeps: Duplicate entry code was entered. 3 Long Beeps: Memory is full. 4 Long Beeps: Unit has reset or is powering up. Busy Signal: Line is busy or Do Not Disturb feature is in effect. 1 Short Beep: Key was pressed on the unit's keypad. 1 Beep: Talk time for a visitor call is lapsing and the unit will beep once per second for the last 10 seconds unless the talk time is extended. Ring Back: The unit is ringing the building. 10 Short Beeps: The unit has granted access. Silence: The keypad has struck out, the unit is being programmed from another source, or an alarm condition exists. 5 Short Beeps: Gate is closing by command. 10 Short Beeps Gate is opening by command. 1 Lift the receiver and press Enters direct command mode Enters direct command mode for unit three The unit is now ready to allow direct commands only! (NPBI / Single Family Residence ONLY) 1A If multiple EL25 units are sharing the same phone line, then a Unit ID Code (1-7 ) will need to be entered at this time. Example 1: Example 2: You can send commands directly to the EL25 from your phone without being in programming mode. This feature is only available for a single-family residence or a manager is sharing a phone line with the EL25.Programming Single Unit OverviewProgramming Responses: Direct Command Responses: Other Responses: To Enter a Direct Command from a Residence Phone: Sending Direct Commands from the Resident's Phone Page 9 Programming Multiple Units Overview Note: You cannot program a unit within a multi-unit chain from a local/remote DTMF phone (Touch-Tone) unless you know the unit's ID number. Therefore, you can only verify the unit number while programming from the unit's front keypad. Up to seven (7) EL25s can be installed on a single telephone line. Each unit must have a “Unique Unit ID” number and the “Number of Units in Chain” assigned to it. If you make an error during an entry, press the asterisk key (*) to begin again. Then Then 1 Press 2 Unit ID Number (1-7), Then 3 Total Number of Units in Chain (1-7), Then The unit ID identifies each unit within a chain. Adding or removing EL25s will require the unit ID's to be re-entered. Factory Setting: Unit ID 1 and Number of Units in Chain 1. This allows you to verify a unit's number within a chain. When you perform this step, the unit will respond with the number of beeps corresponding to its unit ID number. Two beeps, for example, mean the unit is number 2 in the chain. Programming Multiple Units Overview Programming Multiple Units Overview Set the Unit ID Number and Number of Units in Chain: 2 Verify Unit Number: 111 Important: This must be performed for EACH unit in the Chain. EACH unit in the Chain must have the same “Rings Before Answer”. EACH unit in the Chain must have the same “Alternate Prefix”. Unique Unit ID Sequencial Order Number of Units in Chain “7” Unit ID “1” Residence Unit ID “2” Unit ID “3” Unit ID “7” Telco Entrance Box Demarcation Point Example: 16 Factory Setting - 5 Rings 115 Factory Setting - Normal Important: Page 10 Page 11 Page 12 Page 13 Page 14 Page 15 EL25 SetUp “Your Settings” Relay 1- Strike Mode Unlocks Door for 10 sec. Relay 3- Alarm Mode Sounds Siren for 10 sec. Relay 2- Shunt Mode Bypasses/Signals Alarm for Maglock for 40 sec.Relay 4- CCTV Mode Activates Camera for 10 sec. EL25 Main Keypad (Front Door) REX Device (Exit) EL25 Controlling 1 Door LocationDevice Door No. Relay Relay Mode Relay Function Relay Activation Time (Seconds) Front Door Main Keypad Door 1 1 Strike Unlocks Door 10 sec. 2 Shunt Bypasses/Signals Alarm 40 sec. (REX) Exit Request 3 Alarm Sounds a Siren 10 sec. 4 CCTV Activates Camera 10 sec. EL25 Controlling 2 Doors and Vehicle Gate Card Reader(Back Door) Relay 2- Control Mode Turns on Security Light for 60 sec. EL25 Main Keypad (Front Door) Transmitter (Gate Operator) Relay 1- Strike Mode Unlocks Door for 10 sec. Relay 3- Strike Mode Unlocks Door for 10 sec. Relay 4- Strike Mode Opens Gate for 10 sec. Postal Lock Device Main Keypad and Postal Lock Location Front Door Door No. Relay 1 Relay Mode Strike Relay Function Unlocks Door Relay Activation Time (Seconds) 10 sec. Security Light Door 1 2 Control Turns on Security light 60 sec. Wiegand Card Reader Back Door Door 2 3 Strike Unlocks Door 10 sec. Transmitter Gate Operator Door 3 4 Strike Opens Gate 10 sec. Page 16 EL25 EL25 Main Keypad (Front Door) Wiegand Keypad(Exit) Card Reader (Back Door) Card Reader (Manager's Door) EL25 Controlling 4 Doors Relay 1- Strike Mode Unlocks Door for 10 sec. Relay 2- Strike Mode Unlocks Door for 10 sec. Relay 3- Strike Mode Unlocks Door for 10 sec. Relay 4- Strike Mode Unlo...
Questo manuale è adatto anche per i modelli :Telefoni con filo - EL25 (1.98 mb)