valutazioni - 0, GPA: 0
(
)
)
|
Facilità d'uso
1. Point both remotes facing each other by approximately 1 inch apart (see Tips on Learning on previous pages) 2. Press and hold the CODE SEARCH button until the red indicator turns on, then release the button. 3. Press and release the desired Mode button (TV, VCR, etc.), the red indicator blinks then stays on. 4. Press and release the LEARN button, the red indicator blinks then stays on. 5. Press and hold any Original Remote button and move the Original Remote to the left and right, and/ or, up and down in front of the Learning remote IR transmitter. The red indicator will remain on if no IR from the Original remote is found and the red indicator will blink on and off more rapidly when the IR transmitters are lining up. The point where the red indicator blinks most rapidly is where the two IR transmitters are aligned. Note some original remotes will only transmit IR on the initial button press then stop. In these cases, quickly press and release the original remote button repeatedly during this procedure. 6. You can now learn a button from your original remote by continuing from “Step 4” in the “Learning Commands” section on the next page, or, to exit at this point, press and release the CODE SEARCH button The learning feature allows you to “learn” functions from your original remote control. For example - you may want to use your remote to operate the RANDOM PLAY feature from your original CD remote control. This remote is equipped with an “easy learning” feature that allows you to “learn” features (such as RANDOM PLAY from your original CD remote) by following the steps below, and on the next page: 1. Press and hold the CODE SEARCH button until the red indicator turns on, then release the button. 2. Press and release the desired mode button (TV, VCR, etc.), the red indicator blinks then stays on. 3. Press and release the LEARN button, the red indicator blinks then stays on. 4. Press and release the Learning Remote button that you want to teach (e.g. POWER). 5. Point both remotes facing each other by approximately 1 inch apart (see tips on page 14). 6. Press and hold the Original Remote button (e.g. Power) until the red indicator blinks once and stays on. If there is a learning problem, the indicator blinks for three seconds and stays on. If this happens, repeat Steps 4 to 6. 7. Repeat Steps 4-6 for other buttons you want to learn. 8. Press and release the CODE SEARCH button when all desired remote commands are learned. Code Learning is now complete. 6. Line up your remotes (that you’re learning from) in front of the Learning remote, on a hard surface approx. 1 inch apart. 4. 1. 2. 3. 16 17 Troubleshooting Clearing Commands To Clear all Learned Commands under a mode Remote does not operate your product. Clearing learned commands is helpful if, for example, you replace your CD player with another brand or model. If you had learned a feature from your old CD player’s original remote on to this remote (such as RANDOM PLAY), that feature would no longer work for your new CD player. Should you wish to remove or clear one or more “learned” commands, follow the steps below: 1. Press and hold the CODE SEARCH button until the red indicator turns on. Release the CODE SEARCH button. 2. Press and release the button for the mode you want to clear (TV, VCR, etc.). The red indicator blinks off. 3. Press and release the LEARN button TWICE. The red indicator blinks off. 4. Press and release the CODE SEARCH button. The red indicator turns off. All learned Commands under that mode are now cleared. Master Clear - To Clear all Learned Commands under all modes 1. Press and hold the CODE SEARCH button until the red indicator turns on. Release the CODE SEARCH button. 2. Press and release the LEARN button TWICE. The red indicator blinks off. 3. Press and release the CODE SEARCH button. The red indicator turns off. All Learned commands in the remote are now cleared. TV/VCR/INPUT When in TV mode the TV/VCR/INPUT button performs the INPUT source switch function. When in a mode that has been programmed for VCR the TV/VCR/INPUT button performs the TV/VCR antenna switch function. When in a mode that has been programmed for Cable the TV/VCR/INPUT button performs the A.B switch function. When in a mode that has been programmed for SAT the TV/VCR/INPUT button performs the TV/SAT switch function. When in a mode that has been programmed for DVD the TV/VCR/INPUT button performs the DVD Setup function. • Press the mode button of the product you want to control. • Program the remote with a new code. • Install new batteries. (You might have to reprogram your remote after installing new batteries.) • Remote may not be compatible with your product. Remote does not operate some features of your product. • Program remote with a new code. • Remote may not be able to operate all features of your product or button names might be different than your product. Red Indicator blinks after you program a product code. • Remote did not accept the code. • Try ...
Questo manuale è adatto anche per i modelli :Controllo remoto - PM525 (380.95 kb)