valutazioni - 1, GPA: 5
(
)
)
|
Facilità d'uso
One or more four-figure codes are shown for each brand. Note the first code. Be careful! There are separate tables for TV, video, DVD, etc. On our website you can directly select your device typenumber to find the tight code. Make sure you use the codes from the correct table. Press the SELECT key to select TV. Press the key until the TV LED lights up. Keep keys 1 and 3 pressed simultaneously for three seconds until the TV LED flashes twice and then remains lit. 5 Then enter the code noted in step 2 using the digit keys. – The TV LED key will now flash twice. If the LED flashes once for an extended period, the code has not been entered properly or the wrong code has been entered. Star t again from step 2. 6 Point the SRU 7040 at the TV and check that it responds as it should. – If the TV responds to all of the key commands, the SRU 7040 is ready for use. Do not forget to note your code. • If the device does not respond at all, or not to all of the key commands, start again from step 2 and try the next code from the list. English 7 Instructions for use English 3. Keys and functions The illustration on page 3 gives an overview of all keys and their functions. 1 y Standby. . . . . . . . . switches TV, DVD/VCR, STB and AMP on or off. 2 Indicator LEDs 3 LEARN . . . . . . . . . . . switches the SRU 7040 into learning mode. 4 -teletext on/off (disc menu) -text hold -record (VCR/DVD) -wide screen TV -text off -red teletext key -rewind (VCR/DVD) -green teletext key -stop (VCR/DVD) -yellow teletext key -pause (VCR/DVD) -blue teletext key -wind (VCR/DVD) 5 MENU . . . . . . . . . . . . turns the menu on and off. 6 Cursor keys. . . . . . . cursor up, down, left, right in a menu. 7 AV . . . . . . . . . . . . . . . . switches between external inputs of your equipment. 8 2 . . . . . . . . . . . . . . . . . play (VCR/DVD) 9 - VOL + . . . . . . . . . . . adjusts the TV or AMP volume. 0 Digit keys . . . . . . . . . -direct choice of channels and other functions. -source selection keys in amplifier mode (together with SHIFT). ! SHIFT . . . . . . . . . . . . for extra functions.When pressed at the same time as a second key, the second key will get another function. For example: SHIFT + . . . . . . installs your TV. SHIFT + . . . . . . stores TV settings. Try out other combinations with the Shift-key on your device in order to find out which functions are available. Only functions featured on the original remote control are available. @ / . . . . . . . . . . . . . . . . selects between one-and two-figure channel numbers. # 2 22 / SURROUND . selects previous programme/channel. selects surround modes. $ - PROG + . . . . . . . . . selects a previous or following channel. % s . . . . . . . . . . . . . . . . . mutes the sound of the TV or DVD. ^ OK . . . . . . . . . . . . . . . confirms your selection. & BACK. . . . . . . . . . . . . jumps back one level in the menu or turns off the menu. * SELECT . . . . . . . . . . selects TV, DVD/VCR, STB or AMP mode. If the device does not respond at all, or not to all of the key commands, follow the instructions under ‘Setting the remote control’. It is possible that you must enter another code for the device. 8 Instructions for use 4. Extra possibilities Learn a key If you miss cer tain functions from your original remote control on the SRU 7040, the SRU 7040 can learn these functions from the original remote control. You can store a fuction under any of the available keys of the SRU 7040, except LEARN, SELECT and SHIFT. Please, note that any function already stored under a key will be deleted. Example for VCR: Make sure you have the original VCR remote control at hand. Press the SELECT key to select VCR. Press the key until the VCR LED lights up. Press the LEARN key and the target key on the SRU 7040 simultaneously for 5 seconds, until the VCR LED blinks twice and then remains lit. Place both remote controls on a flat surface (like a coffee table) and aim them head-tohead with about 5 - 10 cm in between. 4 Press the button you want to copy on the original remote control. – If the SRU 7040 has learned the code, the VCR LED blinks twice to confirm the signal is stored. – If the LED blinks once for a longer period, the IR signal is not learned by the SRU 7040. Please, tr y a few times and make sure the remote controls are aligned as described in step 3. If the SRU 7040 cannot learn the code after several times trying, it is possible that: – The IR signal of your original device is out of range (the SRU 7040 can only learn IR signals with a carrier signal of 30-60kHz. – The memor y of the SRU 7040 is full. – The SRU 7040 stopped the learning process after 20 seconds if no IR signals are found. Check if your original remote control is working correctly. English 9 Instructions for use English Adjusting device selection (Mode selector) The SRU 7040 is default set for operating TV, DVD (or VCR) STB (settop box, satellite or cable decoder) and AMP (amplifier). You can select the dev...