valutazioni - 0, GPA: 0
(
)
)
|
Facilità d'uso
Example of TV: 1 Turn your TV on manually or use the original remote control. Tune to channel 1. 2 Press the SELECT key to select TV. Press the key until TV lights up in the selector window. If TV does not light up, check whether the batteries are properly inserted (see ‘Inserting the batteries’). 4 Instructions for use 3 Check whether all keys are working. For an over view of the keys and their functions see ‘3. Keys and functions’. – If the TV responds as it should to all of the key commands the SRU540 is ready for use. • If the device does not respond at all or not to all of the key commands, follow the instructions under ‘Setting the remote control’, or for online setup go to: Setting the remote control This is only necessary if your device does not respond to the SRU540. If that is the case, the SRU540 does not recognize the brand and/or model of your device and you need to program the remote control to do so. The example below (TV) instructs you how to do this. You can repeat the same steps for other devices (DVD player/recorder, video recorder, etc.) which you want to operate using the SRU540. Automatically setting the remote control The remote control will now automatically search for the right code for your device. Example of TV: 1 Make sure the TV is switched on and select a channel using the original remote control or the keys on the TV (for example channel 1). The SRU540 emits the ‘switch off TV’ signal for all models of TV that are stored in the memory. • If the device is a DVD player/recorder or video recorder, inser t a disk or tape and star t playback. 2 Press the SELECT key to select TV. Press the key until TV lights up in the selector window. Then keep keys 1 and 3 pressed simultaneously for five seconds until TV in the selector window flashes twice and then remains lit. Press and hold the Standby key of the SRU540. – The SRU540 now star ts emitting all known ‘TV off ’ signals, one by one. Each time a code is sent, TV in the selector window lights up. English 5 5 When your TV switches off (stand-by), release the Standby key of the SRU540 immediately. – The SRU540 has now found a code that works on your TV. 6 Check if you can operate all functions on your TV with the SRU540. • If this is not the case, you can redo the automatic setting. The SRU540 will then search for a code that works better. – After the SRU540 has run through all the known codes, the search will stop automatically and TV in the selector window will stop flashing. – Automatic programming of a TV takes a maximum of 5 minutes. For DVD,VCR and SAT this time is 2 minutes Manually setting the remote control Example of TV: 1 Turn on the TV manually or use the original remote control. Tune in to channel 1. 2 Look up the brand of your TV in the code list at the back of this manual. One or more four-figure codes are shown for each brand. Note the first code. Be careful! There are separate tables for TV, video, DVD, etc. On our website you can directly select your device typenumber to find the right code. Make sure you use the codes from the correct table. 3 Press the SELECT key to select TV. Press the key until TV lights up in the selector window. 4 Keep keys1 and 3 pressed simultaneously for five seconds until TV in the selector window flashes twice and then remains lit. 5 Then enter the code noted in step 2 using the digit keys. – TV in the selector window will now flash twice. If TV flashes once for an extended period, the code has not been entered properly or the wrong code has been entered. Start again from step 2. 6 Point the SRU540 at the TV and check that it responds as it should. – If the TV responds to all of the key commands, the SRU540 is ready for use. Do not forget to note your code. • If the device does not respond at all, or not to all of the key commands, start again from step 2 and try the next code from the list. 6 Instructions for use English SRU540_10_versie_6.qxd 26-04-2005 14:46 Pagina 6 Instructions for use 3. Keys and functions The illustration on page 3 gives an overview of all keys and their functions. 1 y Standby . . . . . . . . . switches TV,VCR, DVD or SAT on or off. 2 . . . . . - teletext on/off ( ); -text off ( ); -wide screen TV ( ); -subtitle ( ); -text hold ( ). 3 MENU. . . . . . . . . . . . . turns the menu on and off. 4 Cursor keys . . . . . . . . cursor up, down, left, right in a menu. 5 AV . . . . . . . . . . . . . . . . switches between external inputs of your equipment. 6 s. . . . . . . . . . . . . . . . . . mutes the sound of the TV. 7 - VOL + . . . . . . . . . . . . adjusts the TV volume. 8 Digit keys . . . . . . . . . . direct choice of channels and other functions. 9 SHIFT . . . . . . . . . . . . . for extra functions.When pressed at the same time as a second key, the second key will get another function. All blue labelled keys can be used together with SHIFT. For example: SHIFT + INSTALL . installs your TV SHIFT + STORE . . . stores TV settings T...