valutazioni - 0, GPA: 0
(
)
)
|
Facilità d'uso
NOTE -If the LED displays one long flash, the code was not recognised. Please go back to step 1 and repeat the procedure, using the next 3-digit code in the list. -If no key is pressed within 30 seconds, you have to start again at step 1. ADVICE Carefully read the complete procedure before starting! You do not know the brand of your TV/you can not find the right code in the code list » auto search: 1 Make sure the device is switched on. 1 3 2 Press and hold keys 1 and 3 simultaneously -for about three seconds- until the green LED lights up. (Release the keys: the green LED should stay on) 4 3 Press the power key to start the search. Make sure that you keep the remote control pointed at your equipment. – Each time the green LED flashes, another code is sent. When the right code is found, the equipment switches off. Immediately press the power key to stop the search. If the green LED flashed again after the equipment switched off, this means you missed the correct code! If you missed the code, follow the next proccedure, starting at step 4. If the LED did not flash again after the equipment switched off, go to step 6. 4 Switch the equipment manually back on. 5 Press ‘PROG-’ (down only!) repeatedly to send previous codes until the equipment switches off again. 6 Press the power key to lock the correct code in the SBC RU610’s memory. – The green LED flashes twice. CHECK Switch equipment on manually. Press a few keys to check correct response. If response is not correct, repeat procedure beginning at step 1. NOTE -The search time averages about 90 seconds. (Maximum search time is 5 minutes for TV). -Autosearch stops automatically after all codes have been tested. MAKE A NOTE OF YOUR CODE! ADVICE Carefully read the complete procedure before starting! Note the code inside the battery case and in the codelist in the centre of this booklet. This may be useful if you ever need to set up the SBC RU610 again. You used the auto search procedure or you forgot to note the code after set up? No problem! You can still ‘read out’ the code from the remote: 1 Press and release keys 1 and 6 simultaneously. Important: after pressing the keys, you have to release them immediately! – The green LED lights up. 2 Press the two digits key. – The green LED goes out. 3 Press key 1 and count the number of times the green LED flashes. This is the first digit of the 3-digit code. (No flashes means the digit is zero.) 4 Press key 2 and count the number of flashes for the second digit. 5 Press key 3 and count the number of flashes for the third digit. 6 Note the code. PROG 1 6 1 2 3 Instructions for use Instructions for use English 7 9 ADVANCED TIPS AND TRICKS A DVICE Carefully read the complete procedure before starting! Back-lighting When you pick up the SBC RU610 and tilt it over about 60 degrees, the main keys for the device you want to operate are automatically back-lit. You can switch off the functional back-lighting feature completely. T IP The automatic back-lighting provides you with unparalleled ease of use, even in the most dimly-lit of rooms. While the remote control is actively being moved about the back lighting stays on. This consumes more power than normal and may require you to change your batteries more frequently. You can easily turn the back-lighting function off to conserve power. To do this please follow the instructions below. To remove the back-lighting completely: • Press keys 7 and 9 simultaneously - for about 3 seconds until the green LED flashes twice. – The back-lighting is now de-activated. Pressing keys 7 and 9 simultaneously again - for about 3 seconds -will return the back-lighting to its preset functional setting. NOTE The back-lighting turns off if you don’t move the remote control or if you don’t press a key within 4 seconds. TROUBLESHOOTING GUIDE • Problem: – Solution: • Device is not responding and the green light does not flash when you press a button. – Replace batteries with two new 1.5 volt, type RO3, UM4 or AAA batteries. • Device is not responding, but the green light does flash when you press a button. – Aim the SBC RU610 at the device and be sure that there are no obstructions between the SBC RU610 and the device. • The SBC RU610 is not performing commands properly. – You may be using the wrong code. Try repeating Set up using another code, listed under your brand, or start the Autosearch Set-up over again to locate the proper code. If the device still doesn’t respond, call the help-line and we’ll put you back on track. • The SBC RU610 drains batteries more frequently. – While the remote control is actively being moved around the back-lighting stays on. This consumes more power than normal and may require you to change your batteries more frequently. You can easily turn the back-lighting function off to conserve power. To do this please follow the instructions in the backlighting section. • You can’t access teletext pages and you were used to use this (.) button to access teletext. – Follow Set u...
Questo manuale è adatto anche per i modelli :Controllo remoto - SBCRU610/87 (506.68 kb)