valutazioni - 2, GPA: 4 ( )

Produttore : Earlex File Size : 535.75 kb File Nome : Lingua di insegnamento:

Align the outline triangle on the handle with the triangle on the accessory. Push the handle into the accessory and twist so that the solid triangles on the handle and accessory are aligned (see Diagram 1). Over time, you may find that your steam cleaning accessories become awkward to assemble to the universal handle. This is due to the steam reducing the lubrication properties of the ‘O’ ring seals. In this event, simply lubricate the ‘O’ ring seals as illustrated (Diagram 2) using washing-up liquid or furniture polish. The Long Handle Attachment (AC01) is designed to be used when cleaning floors or hard to reach areas. To assemble, pass hose through each of the long handle sections, in at the small end out at the large end. Screw the hose nut onto the universal handle and push the long handle sections together and onto the taper on the universal handle (see Diagram 3). You can use one, two or three sections of the long handle. Disconnect in reverse order. If you have any difficulty in disconnecting twist the handles apart. Diagram 2 Seal Lubrication Diagram 1 Assembling Handle Diagram 3 Fitting Long Handle Attachment CASTORS (MODEL SC150 AND SC165 OPTIONAL) The castors are packed separately. Turn the boiler upside down and insert the 3 castors. These should be pushed in hard until they stop. Once installed these remain in place permanently. FILLING SC75 (see Fig.1) Remove elbow filler cap and fill unit to Max. level indicator with clean - preferably hot water. Ensure that the ‘O’ ring is seated correctly on the elbow filler cap and place elbow filler cap lugs into filler hole with the tongue pointing to the TWO O’CLOCK position. Turn the elbow filler cap clockwise to the SIX O’CLOCK position so that the tongue locks into place between the two teeth. SC76, SC125 & SC165 (see Fig.2) Remove filler cap and fill unit to Max. level line or indicator with clean - preferably hot water. Replace filler cap. SC150 (see Fig.3) Remove filler cap and fill unit slowly until the float lifts up in the filler neck, with clean - preferably hot - water. Replace filler cap. Fig.1 Fig.2 Fig.3 SC75 SC76, SC125, SC165 SC150 Do not overfill the unit or hot water will be forced up the steam hose. Screw hose onto threaded outlets of boiler and accessory, hand tight is sufficient. Do not over tighten but do check for hand tight fit from time to time during use. Connect mains lead from unit to power socket and switch on. It can take approx. 20 mins before steam is produced - depending on fill water quantity and temperature. Do not leave unattended and keep children & pets out of the room. Just before full steam production a small amount of bubbling and water will occur at the accessory. Beware of hot water discharge prior to steam emission. If the unit requires refilling, unplug and allow to cool for at least 2 minutes before removing filler cap -Beware of steam - and re-filling. When finished, allow to cool completely and empty unit. Always store unit empty. SAFETY CUT- OUT A safety cut-out is fitted to prevent overheating of the element if water boils below the Min. level. If unit stops boiling during use this may be the cause. Wait for 2 minutes before removing filler cap then re-fill with water. The cut-out will self reset and steam be produced again within 20 minutes. The cut-out will not protect the element if a part filled unit is tilted during use in a way which enables part of the element to be out of the water for longer than 15-20 seconds. CHANGING TOOLS Never remove the hose or change tools when the unit is plugged in. Wait 2 minutes after unplugging before changing tools. Screw the nut, which is on the end of the steam hose, onto the outlet of the tool -hand tight only. FLOOR CLEANER IMPORTANT Some carpets have stain resistant treatments, which have varying active Iives before breakdown. Accordingly it is best to try a small area of carpet that is normally unseen, then allow 24 hours to check whether the steam has any unusual effects on the carpet material, e.g. white streaks. If this happens DO NOT CONTINUE USE - Check with your carpet supplier for further advice. Used correctly the floor cleaner will refresh your carpet by removing surface grime, pet hairs etc. leaving the carpet looking brighter. It is not a dirt extraction system, so cannot necessarily remove deep stains or grease. Attempting to make it do this by longer action of steam may result in watermarking or staining. Cleaning carpets Connect the universal handle and long handle to the floor cleaner head. Fit the cleaning toweI to the head by placing the towel over the floor cleaner head and pulling the drawstring tight. The drawstring can be secured at the back of the floor cleaner. (See diagrams to right) Before using the floor cleaner, use a vacuum to pick up the larger dirt and grit particles. Having prepared the area, plug the boiler unit in and wait for steam to appear at the accessory head. Beware of hot water discharge prior to steam emission. Now beg...

Scarica la tua

Per scaricare, digitare 2 cifre :