valutazioni - 2, GPA: 5 ( )

Produttore : Bissell File Size : 2 mb File Nome : Lingua di insegnamento:

Take care not to run over loose objects oredges of area rugs. Stallingbrush may result in premature belt failure. Tip: make only one trip to the sink by removing the entire portable cleaner. fill and empty in the same trip. 4. 2. 3. WARNING: to reduce the risk of fire, electric shock, or injury, turn power off and disconnect plug from electrical outlet before performing maintenance or troubleshooting. Tip: for best results empty, rinse and dry both tanks before storing. 800.237.7691 9 Operations Upright cleaning mode continued Cleaning your machine continued 2. Rinse front nozzle of any dirt and debris. Remove portable spot cleaner from the WARNING: base of the machine. to reduce the risk of fire, elecunscrew three screws with Phillips screw tric shock or injury unplug from driver and remove nozzle. outlet before servicing. Rinse nozzle out at the faucet. Place back onto the machine by hooking 2. the tabs into the holes on the bottom sides of the machine. secure with screws. 3. the inside of the end caps can be wiped out with a clean paper towel, or for a more thorough clean, the end caps can be taken off and rinsed clean. 4. any loose hair or debris can be pulled from the brush rolls and thrown away. for a more thorough clean, follow directions on page 15 for removal of brush rolls. your machine is now ready to be stored. Tip: Note: Store cleaner in a protected, let all parts dry completely dry area. Since this product uses water, it must not be stored where and replace onto machine. there is a danger of freezing. Freezing will damage internal components and void the warranty. 10 800.237.7691 Operations Portable spot cleaning mode Preparing the machine 1. step on the portable spot cleaning pedal to release the portable spot cleaner. 2. Release flex hose by twisting the hose secure latch clockwise. unwrap flex hose completely. 3. attach the desired tool to the hose grip until it snaps together. make certain the tool is securely attached. 4. twist the Quick Release cord wrap clockwise to unwrap the power cord completely and plug into grounded outlet. Filling tank 1. follow the instructions for filling the tank in the upright cleaning mode section on page 8 Cleaning with Tools: ImPORTANT! If using to clean upholstery, check upholstery tags. Checkmanufacturer’s tag before cleaning. “W” or “WS” on the tag means youcan use your Lift off Deep Cleaner ifthe tag is coded with an “X” or an“S”(with a diagonal stripe through it), or says “Dry Clean Only”, do not proceed with any deep cleaning machine. Do not use on velvet or silk. If manufacturer’s tag is missing or not coded, check with your furniture dealer.”) 1. hold the tool approximately 1" above the soiled surface. Press the spray trigger to apply the cleaning solution to the soiled area. Note: Hold end of hose below the tank water level to help prime theportable spot cleaner. 2. using the brush on the tool, gently scrub the area to be cleaned. 3. apply downward pressure on the tool and pull it toward you. the suction will remove the dirt and cleaning solution. continue until no more dirt can be removed. Adsdfdd ghg bvhcvbbj jkn hnbjgcghh fhl kl Manufacturer’s tag ImPORTANT Check for colorfastness in an inconspicuous place. If possible, check upholstery stuffing. Colored stuffing may bleed through fabric 800.237.7691 11 Operations Portable spot cleaning mode continued Cleaning with Deep Reach™ Tool 1. set tool on soiled surfaces and press the trig-1. ger to spray solution onto the soiled area to be cleaned. 2. slowly move the tool back and forth over the soiled surface, keeping the tool in contact with the carpet. 3. Release trigger and move tool slowly over the soiled area to suction up water and dirt. 4. continue to clean the area, working in small sections, until no more dirt can be removed. Empty dirty tank Follow the instructions under Empty dirty tank section on page 9 of the Upright cleaning mode section. Replacing portable machine on base graphic 1. align the product as the graphic shows, with the cord side on the left and hose side on the right. 2. Push down the portable spot cleaner until you hear it click securely into place. test the fit by pulling up on the carry handle to make sure it is secure. Cleaning portable machine 1. Remove and rinse the tools in clean, running water. dry and replace in the tool storage provided. 2. it is recommended that you suction clean water from a bowl to rinse out the hose. then lift end of hose and stretch out to ensure all water is cleared from hose. 3. coil flex hose around the hose wrap and secure with latch. 4. check suction gate and if it appears dirty, follow steps 1-4 under cleaning suction gate on page 13. 1. 12 Maintenance and care machine care (check regularly) Cleaning suction gate The suction gate automatically diverts air when the portable deep cleaner is detached. This should be checked and cleaned regularly for any dirt and debris. 1. step on the pedal and remove the port...

Scarica la tua

Per scaricare, digitare 2 cifre :