valutazioni - , GPA: ( )

Istruzioni per l'uso Applica, Modello VC50

Produttore : Applica
File Size : 355.47 kb
File Nome :

Lingua di insegnamento:

Il documento viene caricato, si prega di attendere

Scarica la tua primo

Il documento viene caricato, si prega di attendere

Scarica la tua primo

6. A Dust Bag “Full” Indicator will appear in color in the window of the canister lid when the Dust Bag is full (see “Parts” Illustration). When this happens, the vacuum will lose some suction power and the Dust Bag should be emptied. See “Cleaning & Storage.” 7. When finished vacuuming, press the On/Off Foot Pedal to turn the Vacuum Off and unplug. Press the Retractable Cord Pedal with your foot and the cord will wind into the unit. CAUTION: The cord moves fast when retracting. Stand clear of the cord as it rewinds so it does not swing into you as it retracts. See “Cleaning & Storage.” 4 CLEANING & STORAGE 1. NOTE: Always turn off and unplug the unit before cleaning. Carpet freshener or fine powder can clog the bag and cause it to burst if too full. The Dust Bag Full Indicator will alert you that airflow may be blocked or your Dust Bag needs to be emptied. Also check the Dust Filter and Micro-Air Filter regularly to see if they need cleaning (see #6 below). 2. To empty the reusable cloth Dust Bag, for VC80: press the Release Latch at the front of the unit and lift the canister lid. For VC50:Pull up on the Release Latch at the front of the unit and lift the canister lid. (C1 & C2) 3. For VC80:Carefully remove the Dust Bag by grasping it at the collar, sliding it up the track guides, and lifting it out of the unit. For VC50:Pull the Dust Bag Latch forward, grab the bag collar and carefully remove the Dust Bag (see C1 & C2). Slide the Dust Bag Clip off and empty the bag into the trash. Slide the Dust Bag Clip back into place before replacing the bag in the canister. VC50 VC80 C1 C2Release Latch Release Latch 4. The cloth Dust Bag may be hand- washed with soap and water. Hang it Dust Bag Clip up to air dry thoroughly before replacing it in the vacuum. 5. To replace the bag, for VC80:slide Dust Bag the Dust Bag collar all the way down Latch into the track guides. For VC50:Pull the Dust Bag Latch back and clip it onto the collar of the Dust Bag. Be sure to fit the hole in the collar of the Bag over the opening on the inside of the vacuum canister. For both models,close the vacuum lid and be sure it latches shut before operating. 6. Both modelsare equipped with 2 filters. A Dust Filter, which helps prevent dust from getting into the motor, is located on the inside of the canister and visible once you remove the Dust Bag. A Micro-Air Filter is located under the Vent at the back of the unit to help filter out dust particles that may escape into the air. These should be washed every few months and should be replaced after a few washes. 7. To clean or replace the Dust Filter,open the vacuum canister lid. Remove the Dust Bag as explained for your model, and pull the filter holder straight up out of the canister (D). Shake debris into a trash can or use a small whisk broom or sweep away particles. Wash the filter in soap and water. Allow it to air dry completely before replacing it in the Vac. D Dust Filter 5 8. To clean or change the Micro-Filter, press the release at the back of the unit. Remove the Filter Cover (Vent), (E1 & E2) take out the old filter, brush it clean or wash it as explained in “To Clean the Dust Filter.” Allow to dry completely before slipping it back into the Filter Cover. Fit the Tabs at the bottom on the Filter Cover into the lip of the vacuum, then snap the Filter Cover into place. VC80 E1 VC50 E2 WARNING: Do not operate the Vacuum without the Dust Bag and Filters properly installed. 9. To store accessories for VC50:Fit the Dusting Brush over the Crevice Tool and slip the 2-in-1 tool onto the Extension Tube clip for easy storage (F). For VC80:Lift the top cover and fit the Crevice Tool and Dusting Brush into the on-board compartments (see “Parts” Illus.). Be sure you have retracted the cord before storing. Clip the hose and extension tubes onto the back of the canister (F). Lift the vacuum by its handle and stand it upright for compact storage. F 6 Troubleshooting Problem Possible Cause Possible Solution Vacuum won’t start Not plugged in Plug in firmly; press On/Off foot pedal Poor dirt pick up 1. Full or clogged Dust Bag 2. Clogged airflow 1. Empty Dust Bag 2. Check if something is stuck in the hose, tubes, or air 3. Dirty Dust Filter 4. Open suction control (VC80) 5. Hole in Hose 6. Canister Lid open passages 3. Clean the filter 4. Adjust the suction (VC80 ) 5. Replace Hose 6. Close & latch shut Dust Bag “Full” indicator visible 1. Full or clogged Dust Bag 2. Blocked airflow 3. Dust Filter 1. Empty Dust Bag 2. Remove blockage from hose, tubes, or air passages 3. Clean, wash, or change Filter Cord won’t rewind 1. Dirty power cord 2. Cord twisted/jammed 1. Clean the power cord 2. Pull out cord, straighten, push retract pedal Service or Repair Service, if necessary, must be performed by an Authorized Household Appliance Service Center. The Service Center nearest you can be found in the yellow pages of your phone book under “Appliances – Small” or on the Service Center list in this book. For 220V...