Log:
valutazioni - 1, GPA: 3 ( )

Istruzioni per l'uso Admiral, Modello ADM8IB - 10080020

Produttore : Admiral
File Size : 596.73 kb
File Nome :
Lingua di insegnamento: en
Vai a scaricare



Facilità d'uso


Used to hold cleaning solution. 6. Recovery Tank Dome. 7. Vacuum Shoe. 8. Brush Housing. 9. Front Lifting Handle. 10. Cleaning Solution Filter. 11. Solution Tank Fill Hose. 4 5 6 7 8 3 2 1 10 9 11 CONTROLS/COMPONENT LOCATIONS 5 ADMIRAL 86038270 05/22/07 1. Solution Intake Cover. 2. Vacuum Intake Cover. 3. Float Shut-Off. 4. Clean-Out Opening. 5. Pour Spout. 6. Lift Handle. 2 1 3 4 5 6 6 FILLING OPERATIONS ADMIRAL 86038270 05/22/07 6 FILLING THE ADMIRAL NOTE: Use clean bucket of water to fill solution tank Do not put defoamer, solvents, spotter or prespray chemicals in the solution tank. Do not allow water to spill into vacuum motor inlet. Dry spillage from top of solution tank before replacing recovery tank. CHEMICALS Suitable Chemicals Non-Compatible Chemicals Alkalis Aldehydes Detergents Aromatic Hydrocarbons Hydroxides SP Butyls Soaps Carbon Tetrachloride Vinegar Clorox* Chlorinated Bleaches Chlorinated Hydrocarbons Lysol* Methyl Ethel Ketone (MEK) Perchorethylene (perc) Phenolics Trichlorethylene D-Limonene * Product Trademark Names STEP 1 STEP 2 STEP 3 STEP 4 RECOVERY TANK SOLUTION TANK Remove recovery tank FILL LINE Replace recovery tank Add cleaning chemical 8 – 16oz. (237ml – 473ml) Add water 8 gal. (30.3 ltr.) 140°F (60°C) or OPERATIONS ADMIRAL 86038270 05/22/07 7 Remove electrical cord and literature from recovery tank. Fill solution tank (see filling instructions page 6). Adjust brush to proper setting. Note: For good operation the brush must skim the carpet. If circuit breaker trips raise brush to prevent damage to motor or carpet. Plug cord into grounded outlet. Note: Be sure dome is seated on recovery tank, and float shut-off is installed correctly. Turn on brush and vacuum motor switches (“ON”=“I”). Turn on solution switch for continuous spray or set switch to intermittent to allow use of trigger switches. STEP 1 STEP 2 STEP 3 STEP 4 CORRECT INCORRECT 1/8in (3mm) SOLUTION VACUUM CONT INT BRUSH ON ON OPERATIONS ADMIRAL 86038270 05/22/07 8 Select continuous setting to start solution spray or select intermittent setting to enable use of trigger switches to start solution spray. The intermittent setting requires the operator to hold any one of the three trigger switches in the “on” position with the fingers, and is typically used in small areas where short cleaning passes are made. The continuous setting allows the operator to set the switch in the “on” position with one touch, and is typically used in large areas where long cleaning passes are made. Lower machine to floor. Adjust handle to comfortable operating position. Tip machine back by main handle to move to starting point. STEP 5 STEP 6 STEP 7 INT CONT CLEANING PROCEDURE 9 ADMIRAL 86038270 05/22/07 Release intermittent trigger switches or turn off continuous setting on solution switch approximately 1 foot before ending cleaning pass. Push down on handle to raise vacuum shoe and brush before moving to the next cleaning pass. Overlap brush contact area a minimum of 1inch on the ri...

Questo manuale è adatto anche per i modelli :
Aspirapolvere - ADM8IA - 10080010 (596.73 kb)
Aspirapolvere - ADM8IA - 10080010 (596.73 kb)
Aspirapolvere - ADM8IB - 10080020 (596.73 kb)
Aspirapolvere - ADM8IE - 10080030 (596.73 kb)

Scrivi la tua opinione del dispositivo



Il messaggio
Il tuo nome :
Inserire le due cifre :
capcha





categorie