valutazioni - 3, GPA: 4
(
)
)
|
da questo dispositivo ha anche altre istruzioni :
Facilità d'uso
1. Select Guard (virtual door) mode using the Mode/ Power button. - The mode lamp flashes green. 2. Set the fence length using the distance control switch. 3. Install the VIRTUAL GUARD at the entrance of the room to be cleaned. - Install the VIRTUAL GUARD so that the distance detection sensor can form an invisible barrier that the robotic vacuum cleaner cannot cross. Charger VIRTUAL GUARD Room 1 Room 2 Room 3 30cm Distance Detection Sensor A guard (virtual door) is formed. NOTE • When not using the VIRTUAL GUARD, turn the power off. (When not using the robotic vacuum cleaner for long periods of time, separate the batteries to avoid discharging them.) • If the Mode/Power button does not work, it indicates that the batteries have worn out. In this case, replace the batteries. (Specifications: Type D (LR20) alkaline batteries ) • You can additionally purchase a VIRTUAL GUARD from Samsung Electronics customer care Co., Ltd. Operating the cleaner _27 Operating the cleaner 03 operating the cleaner Using the robotic vacuum cleaner Starting /Stopping Cleaning Turning the power on - Remote control : Press the [Power] button. - Main unit: Press the ( ) button. - The main unit buttons, battery level indicator and cleaning mode icons are turned on. Turning the power off - Remote control: Press the [Power] button. - Main unit: Press and hold the ( ) button down for 3 seconds. - All icons except for the battery level indicator are turned off. You can run or stop all robotic vacuum functions. ¦ Each robotic vacuum function only runs when the Power Switch is turned on. ¦ When the robotic vacuum is operating, press the ( ) button to cancel the operation and select a function. Using the remote control OFF ON Turning the power on or off Starting - Remote control : Press the Auto, Spot, Max, Manual or Edgebutton. - Main unit: Select Auto / Spot / Max / Manual / Edge mode by using the ( ) button and then pressing the ( ) button. - When cleaning begins, the robotic vacuum cleaner starts to move. . Pressing the ( ) button without selecting cleaning mode starts to perform the Auto mode cleaning. Stopping - To stop, press the ( ) remote control or main unit button. - When cleaning is stopped, the robotic vacuum cleaner stops. Using the main unit buttons Starting or stopping cleaning 28_ Operating the cleaner Operating the cleaner Using the robotic vacuum cleaner Recharging 1. Press the Recharging button. - The main unit icon ( ) is turned on and the robotic vacuum cleaner will return to the charger. 2. To stop the robotic vacuum cleaner while it is returning to the charger, press the ( ) button. 3. To test the auto charge function, press the Recharging button when the robotic vacuum cleaner is less than 1.5m from the charger. You can have the robotic vacuum cleaner return to the charger to charge the battery by using the Recharging button. ¦ When the robotic vacuum cleaner is operating, press the ( ) button to cancel the operation and press the Recharging button. Troubleshooting when the robotic vacuum cleaner does not return to the charger . Check the installation of the charger - When the charger is in a location where the charger cannot guide the robotic vacuum cleaner to the charger. - When the charger is more than 5m away from robotic vacuum cleaner. : It may require a longer time for the robotic vacuum cleaner to return to the charger. . Manually charge the robotic vacuum cleaner in the following cases. - When the charger is installed in a corner. - When the battery is fully discharged. - When the robotic vacuum cleaner is trapped by an obstacle (furniture etc.) - When the robotic vacuum cleaner cannot pass over the doorsill to the location where the charger is installed. (The height of the doorsill should be about 1cm or less). Using the remote control Using the main unit buttons Operating the cleaner _29 Operating the cleaner 03 operating the cleaner Using the robotic vacuum cleaner Auto Cleaning The robotic vacuum cleaner will move by itself and automatically clean the house until cleaning is completed once. ¦ If cleaning begins when the robotic vacuum cleaner is docked with the charger station, the time to return to the charger is decreased since the robotic vacuum cleaner remembers its original position while moving. ¦ If the battery level becomes too low while cleaning, the robotic vacuum cleaner will automatically return to the charger station and resume cleaning after charging its battery. (Number of cleaning operations resumed: Once) While cleaning When cleaning is complete 2 Cancel the mode. 1 Set the mode. Main unit button Remote control button Configuration Sequence . About the Resume Cleaning function . If the robotic vacuum cleaner has evaluated that cleaning is complete, the resume cleaning function is not performed. . If you move the robotic vacuum cleaner when it is being charged or press a button, the robotic vacuum cleaner judges cleaning to be complete and does not resume cleaning. 1time Do not move the ro...