valutazioni - 2, GPA: 4
(
)
)
|
Facilità d'uso
Mount securely using appropriate length screws into framing studs or spring type wall anchors into wallboard, etc. To charge, mount unit into place by pulling out the hidden wall mount hook at the top of the handle. Next plug power supply plug into nearby 120 volt electrical outlet. Ensure cord is not too tight so as to pull unit off wall mount. The unit can also be charged when placed in a convenient position. RECHARGING (FIG. 3) From new, the rechargeable cells of the product need a minimum charge time of 16 hours to ensure full power. We suggest you fully discharge the product when it is used for the first time as this will help the cells recharge faster. The switch must be in the off (“O”) position, as the product will not charge if it is in any other position. Plug charging cord into dual-pronged outlet on side of unit. While charging, the product may get warm, this is perfectly normal and safe. It can remain on charge indefinitely without damage or danger. It is not possible to “overcharge” the battery cells with the charger provided. Operation POWER SWITCH (FIG. 4) This product is for dry pick-up only. The vacuum has 3 positions: Hard surfaces, Carpet and Off. From the OFF position, push the switch forward to first stop (figure 4A) for hard surfaces. Push forward again to end (Figure 4B) to turn on rotating brush for carpet. To turn the vacuum off, pull the switch all the way back until you can see the OFF icon “O”. FLOOR VACUUM (FIG. 5) To operate as a Floor Vacuum, ensure the DustBuster is in place (figure 5). To turn unit on, refer to Power Switch section of manual. The full tilt handle lets you vacuum comfortably at any height and folds down flat to reach under beds and furniture. The vacuum should be stored in the Floor Vacuum mode. HAND VACUUM WITH BRUSH (FIG. 6) This unit operates as a Hand Vacuum with the brush remaining attached for use on carpeted stairs and other hard to reach areas. When operating in the Floor Vacuum mode, hold onto DustBuster handle, while sliding upper handle access button up and pulling upwards on the handle (figure 6). The power switch operates the same as in the Floor Vacuum mode. DUSTBUSTER (FIG. 7) This unit operates as a cordless hand held vacuum. When operating in Floor Vac mode or Hand Vac with Brush mode (Figure 7) press and hold down the DustBuster release button and pull the unit outward with the handle. The unit will run the same with the power switch in either “ON” or ”Brush” Mode. To replace hand vac, first position nose (opening) over connection to brush head. Next, snap handle into place until you hear “click” into position. IMPORTANT: Do not remove DustBuster when unit is hanging from wall mount. ACCESSORIES (FIG. 8) Accessories are stored on the product (Figure 8) (excluding CFV1200, CFV9600) and are fitted into the nose of the DustBuster for use. See Figure 14 for accessory applications. CLEANING THE PRODUCT (FIGS. 9-13) WARNING: Never use the Dustbuster without its filters. NOTE: The filters are re-usable, do not confuse them with disposable dust bags, and do not throw them away when the product is emptied. We recommend that you replace the filters every 6-9 months. FIG. 9 • Remove the dust bowl by pressing the dust bowl release button and pulling the bowl down and out. To replace the bowl, place it back onto the handle and click firmly into position. FIG. 10 • Empty the dust from the bowl and wash if necessary (see Fig. 10). FIG. 11 • To remove the filter twist it in a clockwise direction. Shake or lightly brush any loose dust off the filter. This product features Black & Decker’s Double Action Filter System™, consisting of 2 nested filters. For best results when cleaning make sure filters are separated. FIG. 12 • Wash the filters regularly using warm, soapy water and ensure that they are completely dry before using again. The cleaner the filters are, the better the product will perform. It is very important that the filter is correctly in position before use. The dust bowl can also be washed in warm soapy water. Ensure that it is dry before re-attaching. IMPORTANT: Maximum dust collection will only be obtained with clean filters and an empty dust bowl. If dust begins to fall back out of the product after it is switched off, this indicates that the bowl is full and requires emptying. FIG. 13 • Never immerse the product in water. A damp cloth and soapy water should be used to clean the exterior of the motor section. Always ensure the product is completely dry before re-use or storing. ECONOMIC USAGE • Your product is very economical to charge. While it is charging it uses less than half the amount of electricity used by a common night light. • When fully charged, the average effective usage times are between 14-16 minutes with brush on and 16-17 minutes with the brush off. • It may take several chargings before these times can be achieved. OTHER INFORMATION If the product does not work, check the following: • The charger was correctly plugged in for ...