valutazioni - 2, GPA: 3.5
(
)
)
|
Facilità d'uso
Continue to clean soiled area, working in small sections, until no more dirt can be removed. Caution: Do not overwet. When the cleaning job is complete, refer to the Maintenance/Storage section below. Turn Power Switch OFF. Make sure to switch SmartMix Dial to WATER ONLY. Unplug Power Cord from outlet and wrap cord around the Quick Release Cord Wrap. Remove and rinse tools in clean water. Dry and replace. Coil Flex Hose through Flex Hose Storage Brackets. Remove Tank-in-Tank. Dispose of dirty water. See The Basics section, page 8. 12 1. 3. 4. 2. 5. CAUTION: PowerLifter Plus uses water and must not be stored where there is a danger offreezing. Freezing will damage internal componentsand void the warranty. Quick Release Cord Wrap™ Flex Hose Storage Bracket Cleaning Technique 1. 2. 3. 4. 5. Maintenance/Storage Quick Release Cord Wrap™ Flex Hose Storage Bracket Cleaning Technique 1. 2. 3. 4. 5. Maintenance/Storage Maintenance/Storage Continued Rinse out Tank-in-Tank and reseat the tank onto the machine. Clean out the Flow Indicator Filter each time it is used to ensure best cleaning performance. Unscrew the Flow Indicator cap, lift out the red Rotor and white Filter. Rinse all three parts in tap water. Replace the Filter and Rotor. Replace the Flow Indicator Cap; turn until snug, do not over-tighten. Wipe all exterior surfaces with a soft cloth. Store cleaner in a protected, dry area. When carpet is dry, vacuum again to remove hair and fuzz that the PowerLifter Plus may have loosened. Pump & Brush Belts Replacement To Remove Broken Pump & Brush Belts NOTE: Turn off machine and unplug from wall outlet. Step on Handle Release pedal and recline Handle on floor (see illustration). Remove the Tank-in-Tank. Set aside (see illustration). Remove the Belt Access Door located near the ReadyTools Dial. Insert a flathead screwdriver into the slot nearest the handle to gently pry off the door (see illustration). 6. 7. 8. 9. 10. 1. 2. 3. When filling bottle or storing unit, set Dial to: Cap Rotor Filter Tip: SmartMix Bottle may be stored with concentrate ready for your next cleaning job. Make sure dial is turned to the WATER ONLY Setting when storing 1 2 3 13 14 To Remove Broken Pump & Brush Belts-Continued Turn the machine onto its side so the belt access area is facing upward (see illustration). On the bottom of the machine, near the belt access area, is a red Retainer Plate that holds the black brush arm and brush in place. Using a Phillips head screwdriver remove the screw that holds the red Retainer Plate in place. Set red Retainer Plate and Phillips head screw aside (see illustration). Remove the black brush arm that holds the brush in place. Set the black brush arm aside (see illustration). Remove the "toothed" Brush Belt from the Brush, then from the red Pump Pulley. Set the "toothed" Brush Belt and Brush aside. Locate and remove the broken Pump Belt. 4. 5 6. 7. 8. 5 4 6 7 8 Red Retainer Plate 5 4 6 7 8 Red Retainer Plate 15 To Install The Replacement Pump & Brush Belts With the unit still on its side, loop one end of the replacement Pump Belt around the red Pump Pulley and the other end around the silver motor shaft (see illustration). Do not twist the replacement Pump Belt. Re-install the “toothed” Brush Belt first onto the red Pump Pulley and then onto the “toothed” end of the Brush (see illustration). Re-install the Brush into the base of the unit. (see illustration) Place the black brush arm onto the Brush and slide black brush arm into original position (see illustration). 1. 2. 3. 4. 2 1 3 4 Silver Motor Shaft 2 1 3 4 Silver Motor Shaft 16 To Install The Replacement Pump & Brush Belts-Continued Re-install the red Retainer Plate and Phillips head screw (see illustration). Using your finger, gently spin the replacement Pump Belt on the silver motor shaft (see illustration). If assembled correctly, the replacement Pump Belt should rotate freely around the silver motor shaft and drive pulley without obstruction. The Brush should also rotate freely when the silver motor shaft is turned. Turn the machine right side up. Replace the Tank-in-Tank and Belt Access Door (see illustration). Assembly is now complete. If you have any questions, or if you have any trouble installing your replacement Pump Belt, please call BISSELL Consumer Services at 1-800-237-7691. Or visit the BISSELL website: 5. 6. 7. 5 6 7 Red Retainer Plate Belt Access Door 5 6 7 Red Retainer Plate Belt Access Door WARNING: To reduce the risk of fire, electric shock, or injury, unplug machine fromoutlet before servicing. Reduced spray or no spray. Possible Causes Remedies Bladder may be empty Turn power OFF, refill tank with hot tap water. SmartMix may be empty Refill bottle with formula. The lint screen may be clogged Turn power OFF, clean out lint screen, follow step 2 on page 8. Tank-in-Tank may not be seated properly Turn power OFF; remove and reseat tank. Pump may have lost prime Turn power OFF; after 1 minute, turn ON and depress Sp...