valutazioni - 3, GPA: 5
(
)
)
|
Facilità d'uso
Do not use on velvet or silk. If manufacturer’s tag is missing or not coded, check with your furniture dealer. 2. Check for colourfastness in an inconspicuous place. 3. If possible, check upholstery stuffing. Coloured stuffing may bleed through fabric when wet. 4. Plan activities to give upholstery time to dry. 5. Vacuum thoroughly to pick up loose debris and pet hair. Use a vacuum with a brush attachment and a crevice tool to clean in fabric folds and tufts. 6. To begin cleaning with attachments, follow the instructions on pages 7-8 for filling the 2-in-1 water tank. 7. Set the ReadyTools dial to the TOOLS setting. This will allow spray and suction from the hose. 8. Attach the cleaning tool to the end of the hose. Adsdfddghg bvhcvbbj jkn hnbjjkvhgcghhjj fhl kManufacturer’s tag Tip: To clean with sliding crevice tool, slide brushes forward to clean stain, slide back to suction 7. 10 operations operations Ready Tools™ continued 9. Clean by pressing the trigger to spray solution onto the area to be cleaned. Slowly move the tool back and forth over the soiled surface. Release the trigger to suction dirty water. Continue to clean in the area, working in small sections, until dirt is removed. Caution: Do Not Overwet. 10. When finished cleaning, remove and rinse tool(s) in clean, running water. 11. It is recommended that you suction clean water from a bowl to rinse out the hose. 12. Before wrapping hose onto tool rack, lift end of hose and stretch out to ensure all water is cleared from hose. 13. Wrap flex hose around tool rack. 14. Empty 2-in-1 water tank and rinse out, following instructions on pages 9 through 10. 15. If the ReadyTools dial becomes difficult to turn, the diverter assembly that holds the dial may need to be cleaned. To clean, first remove nozzle and locate screw that holds the diverter assembly in place. With a Phillips screwdriver, remove the screw and set aside. 16. Remove diverter assembly; hold under running water making sure water flows through and around the dial. Turn the dial about 10 times clockwise and 10 more times counter clockwise. This should free up any debris. 17. Wipe diverter assembly with a soft cloth and replace back on machine. Replace nozzle. 18. Return ReadyTools dial to FLOOR CLEANING setting. 12. 11. Run water through here 15. 16. Screw 11 Maintenance and care Maintenance and care Machine care For best results, a few simple steps can assure your machine is well maintained after your cleaning is complete. 1. Turn power switch OFF. Unplug the machine and wrap the power cord. 2. After emptying the 2-in-1 water tank, rinse it with running hot tap water, taking care to clean underneath and around the heavy duty bladder. Clean out red lint screen. Removable nozzle may be rinsed if necessary. Refer to page 9. 3. Replace the 2-in-1 water tank on the machine. 4. Any loose hair or debris can be pulled from the brush roll and thrown away. 5. To clean attachments, remove from hose and rinse in clean, running water. Dry before storing. Clean the hose by suctioning clean water from a bowl. Before wrapping back on machine, lift end of hose and stretch out to ensure all water is cleared from hose. Refer to page 11, illustrations 11 and 12. 6. Wipe the machine’s exterior with a soft cloth. 7. After carpet is dry, vacuum again to remove hair and fuzz. Machine storage Put the unit away in a closet or basement for the next use. Store cleaner in a protected, dry area. Since this product uses water, it must not be stored where there is a danger of freezing. Freezing will damage internal components and void the warranty. 12 Troubleshooting WARNING: To reduce the risk of fire, electric shock or injury, unplug from the outlet before servicing. Reduced Spray OR No Spray Possible causes Remedies Troubleshooting WARNING: To reduce the risk of fire, electric shock or injury, unplug from the outlet before servicing. Reduced Spray OR No Spray Possible causes Remedies Slots Pump Belt A. 1. Bladdermaybeempty 1. TurnpowerswitchOFF;Refillbladder withcleanhottapwater. 2. 2-in-1tankmaynotbeseatedproperly. 2. TurnpowerswitchOFF;removetank andreseattanks. 3. Pumpmayhavelostprime. 3. TurnpowerswitchOFF;after1minute turnONanddepresssprayreleasetrigger. 4. Thepumpbeltmaybebroken. 4. TurnpowerswitchOFFandunplugfromtheoutlet.To checkifapumpbelthasbroken,youwillneedaflat B. headscrewdriver. A. Insertthebladeendintotheslotofthebeltaccess doortorelease.Examinethebeltforbreakage.You shouldbeabletoseethepumpbeltloopedaroundthe motorshaft.Ifitisbrokenormissing,pleasereferto ReplacementPartsonpage14.Areplacementbeltmay beorderedbycallingBISSELLConsumerServices Completeinstallationinstructionswillaccompanythe replacementbelt. B. Whenreplacingbeltaccessdoorbesuretolineup slotsofbeltaccessdoorwithslotsinmachine, slidedoorintoplaceandsnapshut. DirtLifter PowerBrush Does Not Turn Possible causes Remedies 1. Thebrushbeltorpumpbeltisofforbroken. 1. RefertoRemedy4abovetocheckifbrus...