valutazioni - 4, GPA: 4
(
)
)
|
Facilità d'uso
NOTE: Remove the Tank-in-Tank, following steps 1 and 2 at the top of the page. Carry the Tank-in-Tank, like a bucket, to the sink. Remove Tank Lid. Pour out dirty water. After each use, remove and rinse the Lint Screen located on the Tank Lid. A. Remove Tank Lid. B. Remove Lint Screen and rinse under faucet. Remove any debris caught in Lint Screen. C. Re-insert Lint Screen on Tank Lid. The screen will click into place. D. Replace Tank Lid. Refill with cleaning solution and clean tap water—follow steps 3-5 above. When a cleaning job is complete, rinse out the Tank-in- Tank by running clean water between the bladder and the tank. Return the Tank-in-Tank to the machine, follow step 6 above. Refer to the Maintenance/Storage section on the next page for final cleanup. 1. 2. 3. 1. 2. 4. To Fill The Tank-in-Tank When It’s Time To Empty The Tank-in-Tank 3. 5. 6. 4. 5. 6. 1 Handle Release Rotate Handle 3 to Unlatch 2 4 65 Lint Screen 1 2B Lint Screen 5 Tip: 2C Latched A special red float device in the tank will cause the cleaner to stop removing solution from the carpet. The motor sound will rise in pitch to let you know the dirty water tank is full. Normal Cleaning 1. 2. 3. 4. 5. 6. 7. 1. 2. 3. 4. 5. Plug the PowerSteamer into a proper outlet and turn ON the Power Switch. Make one slow forward and backward wet pass by pushing the SprayTrigger. Caution: Do not overwet. Release the Spray Trigger and make one slow forward and back pass over the same area to remove any residual dirty water. Repeat cleaning passes without pressing the Spray Trigger until you can’t see any more water being suctioned up. When cleaning job is complete, refer to Maintenance/Storage. Maintenance/Storage Turn Power Switch OFF. Unplug Power Cord from outlet and coil cord around Power Cord Quick Release. Remove Tank-in-Tank. Dispose of dirty water. Rinse out Tank-in-Tank and re-seat the tank onto the machine. Wipe all exterior surfaces with a soft cloth. Store cleaner in a protected, dry area. When carpet is dry, vacuum again to remove hair and fuzz that the PowerSteamer may have loosened. Pump Belt Replacement NOTE: Turn off machine and unplug from wall outlet. To Remove Broken Pump Belt 1. 2. Step on Handle Release pedal and recline Handle on floor (see illustration). Remove the Tank-in-Tank. Set aside (see illustration). OFF ON Power Cord Quick Release CAUTION: PowerSteamer uses water and must not be stored where there is a danger offreezing. Freezing willdamage internal components and void the warranty. 7 21 8 Remove the Belt Access Door. Insert a flathead screwdriver into the slot nearest the handle to gently pry off the door (see illustration). Turn the machine onto its side so the belt access area is facing upward (see illustrations). On the bottom of the machine, near the belt access area, is a White Retainer Plate that holds the black Brush Arm and brush in place. Using a Phillips head screwdriver remove the screw that holds the White Retainer Plate in place. Set White Retainer Plate and Phillips head screw aside (see illustrations). Remove the black Brush Arm that holds the brush in place. Set the black Brush Arm aside (see illustrations). Locate and remove the broken Pump Belt. With the unit still on its side, loop one end of the replacement Pump Belt around the Red Pump Pulley and the other end around the silver motor shaft (see illustration). Do not twist the replacement Pump Belt. Re-install the Brush into the base of the unit. Place the black Brush Arm onto the Brush and slide black Brush Arm into original position (see illustrations). Reattach White Retainer Plate and secure with screw. To Remove Broken Pump Belt Continued 3. 4. 5. To Replace Broken Pump Belt 3. 7. 1. 6. 2. 43 5 White Retainer Plate 7 6 21 3 9 Troubleshooting WARNING: To reduce the risk of fire, electric shock, or injury, unplug machine from outlet before servicing. Lift Here Insert Screwdriver Blade Here 1 2 1 2 3 4 5 3 4 5 Reduced spray or no spray. Possible Causes Remedies Bladder may be empty Turn power OFF, refill tank with hot tap water. The lint screen may be clogged Turn power OFF, clean out lint screen, follow step 2 on page 6. Tank-in-Tank may not be seated properly Turn power OFF; remove and reseat tank. Pump may have lost prime Turn power OFF; after 1 minute, turn ON and depress Spray trigger. The Pump Belt may be broken Turn power OFF and unplug machine from outlet. To check if a Pump Belt has broken, you will need a flathead screwdriver. Insert the blade end into the lower slot of the Belt Access Door to release the latch. If necessary, insert the blade end into the upper slot to release the upper latch. Examine for belt breakage. You should be able to see the Pump Belt looped around the motor shaft. If it is broken or missing, please refer to the part numbers and descriptions on page 11 before calling BISSELL Consumer Services. Complete installation instructions will accompany the replacement belt. PowerSteamer is not picking up solution. Possible...