valutazioni - 2, GPA: 4
(
)
)
|
Facilità d'uso
Rinse thoroughly, dry and store. Check manufacturer’s tag before cleaning. “W” or “WS” on the tag means you can use your PowerSteamer If the tag is coded with “X” or “S” (with a diagonal strike through), or says “Dry Clean Only,” do not proceed. Do not use on velvet or silk. If manufacturer’s tag is missing or not coded, check with your furniture dealer. Check for colorfastness in an inconspicuous place. If possible, check upholstery stuffing. Colored stuffing may bleed through fabric when wet. Plan activities to give upholstery time to dry. Vacuum thoroughly to pick up loose debris and pet hair. Use a vacuum with a brush attachment and a crevice tool to clean in fabric folds and tufts. Set up the machine following instructions in The Basics sec- tion, on pages 6-9. Using the Measuring Cup provided, pour BISSELL Advanced Deep Cleaning Formula into the Tank-in-Tank. Set the ReadyTools™ dial to Tools or PreTreat. 1. 2. Bare Floor Cleaning Technique 1. 2. 3. 1. 2. 3. Adsdfdd ghg bvhcvbbj jkn hnbj jkvhgcghhjj jhffhl kllgh Manufacturer’s Tag How To Clean Upholstery and Small Areas Important - Check Upholstery Tags 3. 4. 5. 6. Machine Preparation WARNING: To reduce the risk of fire, electric shock or injury unplug from outlet before servicing. ug310-5907_1692-1694_205.indd 10 4/18/05 9:20:04 AM ug310-5907_1692-1694_205.indd 10 4/18/05 9:20:04 AM Maintenance/Storage CAUTION: PowerSteamer uses water and must not be stored where there is a danger of freezing. Freezing will damage internal components and void the warranty. 2 3 4 5 6 7 9 Turn Power switch OFF. Unplug power cord from the outlet and coil around Power Cord Quick Release. Remove and rinse tools in clean, running water, let dry and replace in tool caddy. Coil flex hose through storage brackets. Remove Tank-in-Tank,™ dispose of dirty water. See The Basics section, on page 6. Rinse out the Tank-in-Tank™ and reseat the tank unto the machine. Wipe all exterior surfaces with a soft cloth. Store cleaner upright in a protected, dry area. When carpet is dry, vacuum again to remove hair and fuzz that the POWERSTEAMER may have loosened. Turn the machine off and unplug from wall outlet. Step on the release pedal and recline the handle down onto floor. Remove the Tank-in-Tank. Set them aside. Remove Belt Access Door located near the ReadyTools Dial. Insert a flat head screwdriver into the slot nearest to the handle and gently prying the access door off. Turn the machine onto its side so the belt access area is facing upward. On the bottom of the machine, near the belt access area, is a Red Retainer Plate that holds the black brush arm and brush in place. Using a Phillips head screwdriver remove the screw that holds the Red Retainer Plate in place. Set Red Retainer Plate and Phillips head screw aside. NOTE: For 1693 Model series, remove stationary brush (skip step 6 and 7) Remove the black brush arm that holds the brush in place. Set the black brush arm aside. Remove the “toothed” Brush Belt from the Brush then from the Red Pump Pulley. Set the “toothed” Brush Belt and Brush aside. Locate and remove the broken Pump Belt. 1. 2. 3. 5. 6. 6. 7. 1. 2. 3. 4. 7. 8. Pump Belt and Brush Belt Replacement 4. 5. 8. 9. 9. Power Cord Quick Release Flex Hose Storage Bracket 8 11 WARNING: To reduce the risk of fire, electric shock or injury unplug from outlet before servicing. ug310-5907_1692-1694_205.indd 11 4/18/05 9:20:04 AM 12 With the unit still on its side, loop one end of the replacement Pump Belt around the Red Pump Pulley and then the other end around the silver motor shaft. Do not twist the replacement pump belt. Re-install the "toothed" Brush Belt first onto the Red Pump Pulley and then onto the toothed end of the Brush. Re-install the brush into the base of the unit. Place the black brush arm onto the Brush and slide black brush arm into original position. Re-install the Red Retainer Plate and Phillips head screw. Using your finger, gently spin the replacement pump belt on the silver motor shaft. If assembled correctly, the replacement Pump Belt should rotate freely around the silver motor shaft and drive pulley without obstruction. The brush should also rotate freely when the silver motor shaft is turned. Turn the machine right side up and replace the Tank-in-Tank and belt access door. Assembly is now complete. If you have any questions, or are having trouble installing your replacement pump belt, please call BISSELL Consumer Services at 1-800-237-7691. 1. 2. 3. 5. 6. 4. 7. 8. To Install The Replacement Pump Belt 1. 2. 3. 4. 5. 6. 7. 12 With the unit still on its side, loop one end of the replacement Pump Belt around the Red Pump Pulley and then the other end around the silver motor shaft. Do not twist the replacement pump belt. Re-install the "toothed" Brush Belt first onto the Red Pump Pulley and then onto the toothed end of the Brush. Re-install the brush into the base of the unit. Place the black brush arm onto the Brush and slide black brush arm into original positi...
Questo manuale è adatto anche per i modelli :Aspirapolvere - 1693 (1.03 mb)
Aspirapolvere - 1694 (1.03 mb)